Ask Experts Questions for FREE Help !
Ask
    bigalgar8's Avatar
    bigalgar8 Posts: 3, Reputation: 1
    New Member
     
    #1

    Jan 29, 2010, 03:55 PM
    Valve knob will not ignite water heater
    Tried to lite water heater by holding red button and pushing valve knob but no clicking heard
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
     
    #2

    Jan 29, 2010, 04:47 PM

    This sounds backwards. You should be holding the valve nob down(in the pilot possition) and then repeatedly push the red button(it is your sparker).
    bigalgar8's Avatar
    bigalgar8 Posts: 3, Reputation: 1
    New Member
     
    #3

    Jan 29, 2010, 07:07 PM

    I've tried that also and still no spark
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
     
    #4

    Jan 29, 2010, 07:58 PM

    About three inches form the button that you press to make it click there is a push together connection, pull this apart, (not what I am going to telol you to do might give you a little of a shock) Hold the wire that is coming from the button in one hand and click with the other. If you get a shock the sparker is good if you don't it is bad and needs to be replaced. But I have never seen one that is bad. So continue to use the sparker and watch where the connection is and make sure it is not sparking to the water heater jacket from there.
    bigalgar8's Avatar
    bigalgar8 Posts: 3, Reputation: 1
    New Member
     
    #5

    Jan 29, 2010, 08:26 PM

    Yes there spark, but wire leads into in case area. Do I remove screws to access it. If yes I will try tomorrow Thank you
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
     
    #6

    Jan 30, 2010, 10:57 AM

    No you do not remove anything because if you do it has to be resealed.

    Instructions are: 1. make sure that the gas valve is turned on, this should be in the line running to the water heater.

    2. Turn the knob on top of the valve to pilot, press down, it should depress about 1/4 to 3/8 of an inch.

    3. While holding this knob down click the spark button several times, continue holding the knob down that is pointed to pilot, this should be held for about 35 to 45 seconds.

    4. After holding down the knob let it loose and through it counter clockwise to the on position.

    5. Now turn the large knob that is on the front of the thermostat to the point where the letter B aligns with the arrow pointer. This big knob is the temprature control, if B is too hot turn to A, if B is not hot enough turn higher than the B. As you turn this knob you should hear the burner of the water heater light.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Surging water pressure & leaking water heater relief valve [ 19 Answers ]

Just recently the pressure of our water in the house surges when we turn a faucet on, and the city water company verified that our pressure in the house when we open a faucet is higher than the pressure in the lines in the street, and after the water runs is at a normal pressure (meaning their...

Water leaking from cut-off valve knob (clear plastic) [ 28 Answers ]

The cut-off valve is no longer shutting the water off to my toilet tank and it is also leaking a few drops right at the knob that you turn to shut the water off. How can I fix that?

No Shut Off Valve between water heater and bathroom sink valve [ 14 Answers ]

I have a constant drip in my bathroom sink. After a little trouble shooting, I came to the conclusion that my hot water valve underneath the sink is the culprit. I traced the pipe down the wall, into the basement and to the water heater. The only thing between the water heater and the old valve in...

State select 75 gal water heater pr675xrvit about 4 yrs old. Fail to ignite. [ 3 Answers ]

Gas water heater. 75 gallons. State select model pr6 75 xrvit. Installed in 2005. Has been working well. Last few weeks, it stopped to come on. I was abled to cycle the ON-OFF toggle switch and restart. Usually take a few try. The LED status light shows 101001. According to the manual:...

Very low water pressue to house after replacing leaking valve on water heater [ 1 Answers ]

I replaced the leaking valve leading to the hot water heater, drained the hot water heater, turned the main valve to the house back on and now have very low water pressure to the house (cold and hot) The house has galvanized metal pipes... HELP please!:confused:


View more questions Search