Ask Experts Questions for FREE Help !
Ask
    KyroD79's Avatar
    KyroD79 Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Jan 20, 2010, 06:45 PM
    Replacing galvanized drain and vent pipe with PVC
    Ok, so here's my dilemma. I have a home built in the 60's. The plumbing is all galvanized steel for water lines and drain lines. I recently started updating my bathroom and we have always had problems with the sink draining very slowly.

    Recently I became aware
    That the galvanized steel tends to corrode quickly causing clogs. Therefore, I would like to replace at least some of the pipe with PVC. However, I am unsure of the process of this. THe sink drain has a fulll piece of pipe about 6-8 feet or so which goes from the horizontal drain pipe heading into the toilet stack to
    A fitting for the p trap then continues I would assume to the roof. What is the easiest way of replacing this pipe. Is cutting the answer? And if so, do I need to be worried about the weight of the pipe overhead that continues to the roof, or is this pipe securely fastened to something? Any help would be appreciated
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
    		  
    #2

    Jan 20, 2010, 08:40 PM

    In a day or so, I believe you can post pictures. Use "go advanced/manage attachments" to do so.

    Yep, you do need to worry about the weight of the pipe. Removing shingles and replacing the boot is also temperamental.

    Are you planning to replace the toilet and it's associated plumbing?

    Fernco couplings are the easiest way to join to a galvanized stub.

    Do you have a cast iron main drain?
    KyroD79's Avatar
    KyroD79 Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Jan 20, 2010, 09:00 PM

    Yes I do have a cast iron main drain . I do plan on replacing the toilet but am reluctant to replace all the other pipe, although I know its what would be best. As of right now, I am mostly concerned with the sink drain pipe.

    Could you explain a little more about the Fernco Couplings... unfamiliar with them

    Thanks
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
    		  
    #4

    Jan 20, 2010, 09:13 PM

    It's a banded rubber coupling. Fernco Proflex Shielded Plumbing Flexible Coupling, fernco, fernco coupling, fernco couplings, fernco fitting, Shielded Drain Pipe Coupling, Shielded Waste Pipe Coupling, Shielded Vent Pipe Coupling, Flexible Shielded Plumbing Coupling | Fernco

    They are available at Home Depot.

    These basically provide a transition connector between say PVC and galvanized.


    Here is another use. http://www.ehow.com/how_4968998_conn...iron-pipe.html

    I think they mean in the page to support the PVC so the coupling doesn't deform.

    If your sink drains directly into the cast iron, Tom has some better ideas.

    Removing the galvanized pipe via the threads isn't going to happen easily

    Is there a lead/oakum joint that you will be tying into?
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #5

    Jan 21, 2010, 06:42 AM
    As of right now, I am mostly concerned with the sink drain pipe. Could you explain aFerncoCouplings... unfamiliar with them
    If this were my call I'd cut the galvanized off at the stack leaving a few inches of the old galvanized to attach a Shielded Coupling, see image) to.
    You may then transition to PVC and complete the drain and trap. Since you won't be cutting into the stack to do this I wouldn't worry about it falling down. Good luck, Tom
    Attached Images
     
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Replacing galvanized steel drain pipe [ 12 Answers ]

I am truly desperate for some suggestions or reassurance concerning a plumbing issue we are having. Our home is 50 years old and the washing machine drain overflows each time we do a load of laundry. I have read your suggestions for a utility sink to act as a resivour tank but my husband doesn't...

Replacing Galvanized Pipe w/PVC [ 4 Answers ]

Our house was built in 1966; we purchased it 3 months ago. Most of the plumbing is newer w/black pvc for sewage etc. Recently, I was under the house checking things and making sure all is going to be good for the winter. Here is what I found. The galvanized pipes under the kitchen area that...

Replacing Galvanized Drain Section [ 1 Answers ]

I'm in an older house and need to replace a section of pipe draining from the kitchen sink. Two caveats that are relevant, however: 1. There are clearly two different types of pipe. One is darker (I assume galvanized steel), one is lighter, almost like aluminum. Both have corroded to the point...

Vent pipe turned into drain pipe and drain pipe into vent pipe [ 3 Answers ]

I recently began to remodel my laundry room. I wanted to move the washing machine 3 ft from its current spot. When I removed the sheet rock I found that the vent pipe is between the current washing machine drain and where I am moving my washing machine. I wanted to avoid breaking into the slab....

Broken PVC (vent/drain) pipe at joint [ 1 Answers ]

So I had a clogged drain and I was checking the trap. I was under the house and was working on the pipes when I accidentally broke the drain pipe off at a T joint just below the trap. How can I remove the broken end from the joint since it was solvent welded in? Or what else can I do?

View more questions Search