Ask Experts Questions for FREE Help !
Ask
    Kamie45's Avatar
    Kamie45 Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Jan 20, 2010, 02:54 PM
    Texas furnace stopped working
    Hi I have a Texas furnace I recently changed the circuit board, however it stopped working and the light on the board is not coming on, I checked the power to the unit and everything seems OK. Can anyone help, I live in NY and it is very cold, I would appreciate any help that is our there
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Jan 20, 2010, 02:58 PM
    I have never heard of a Texas furnace. Does it have an Exact model number?
    Kamie45's Avatar
    Kamie45 Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Jan 20, 2010, 03:11 PM
    Yes ABA140NI5R
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #4

    Jan 20, 2010, 03:32 PM
    The brand is All Style.

    Here is your factory install/service manual.

    http://www.allstyle.com/installation...lersManual.pdf

    The wiring diagrams and all else is in this manual.

    If the light to the board is not on then power to the unit somewhere is not being applied. Check the safety switch that is located at the blower motor access door(Called the blower door interlock on the wiring diagram). Those have been known to fail or not activate if the door is loose. I did not notice a fuse on the board but look for yourself.

    If the above fail to find the problem then you will have to sound the power out problem step by step starting at the furnace switch then into the unit itself. Make sure to check all connections including any plug in item. Usually if you unplug and plug back in the contacts will clean themselves. Should be an easy find.
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #5

    Jan 20, 2010, 03:36 PM
    Do the have BIGGER furnaces in Texas than they do anywhere else?
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Kirkland Signature, by whirlpool; Dryer stopped heating and timer stopped working [ 2 Answers ]

I have a Kirkland Signature, by whirlpool Dryer that stopped heating and timer stopped working at the same time. What may have caused this?

Furnace stopped working [ 1 Answers ]

Hi, I am getting 7 red flashes on the status indicator light for my Luxaire furnace, model GM9S060B12UP11G. The Diagnostic Fault Codes indicate "ignition lockout due to retries". The ventor motor starts as do the burners, there are several clicks heard and then the whole thing shuts down. The whole...

Trane Gas Furnace just stopped working [ 2 Answers ]

I have a Trane XL80 gas furnace. It also has a heat pump for ref. Today, the temp in our home dropped and I noticed that the furnace was not working. I opened it up, and vacuumed it out, and have no idea why it started working. All was good! However, hours later, the temp is again...

Furnace stopped working. [ 1 Answers ]

Unfortunately, it seems our furnace stopped working a couple of days ago. I can get the fan to work if I set it to "on" but not "auto". And even if the fan is blowing in the "on" setting, the air never warms up. I've tried playing with the thermostat and resetting the whole thing a few times from...

Previously working electrical outlets stopped working [ 2 Answers ]

Hi Everyone A wall of electrical outlets in my kitchen just stopped working. They were working just fine about a month ago. I tried checking the circuit box, and turning the circuits on/off just to make sure anything that has been tripped was turned on back again. But it didn't work for the...

View more questions Search