Ask Experts Questions for FREE Help !
Ask
    crananto12's Avatar
    crananto12 Posts: 3, Reputation: 1
    New Member
     
    #1

    Dec 26, 2009, 12:17 PM
    How do I change when emer heat automatically comes on instead of Hpump t8611g honeywe
    My honeywell t8611g goes to emergency heat when I change temp up only two degrees. How do I change this so it will stay on heat pump when I change the temp up to three degrees?
    KC13's Avatar
    KC13 Posts: 2,556, Reputation: 99
    Ultra Member
     
    #2

    Dec 26, 2009, 12:48 PM

    Here is a manual. Page 15 describes the intellegent recovery feature. It should be allowed to manage temperature changes to minimize or avoid auxiliary heat usage. Manual adjustments exceeding 1 degree from current setpoint usually activate auxiliary. http://www.honeywell-thermostat.com/...611gmanual.pdf
    crananto12's Avatar
    crananto12 Posts: 3, Reputation: 1
    New Member
     
    #3

    Dec 26, 2009, 01:04 PM
    Is there a way to change this though to say three degrees? I appreciate the answer and I understand how the AIR works. I want to change the programming so that Aux (emer) heat comes on only if there is a three degrees or more increase in temp.
    KC13's Avatar
    KC13 Posts: 2,556, Reputation: 99
    Ultra Member
     
    #4

    Dec 26, 2009, 01:09 PM

    Some will allow enabling of additional setup options, with addition of optional outdoor sensor. Your model may have a limiting option based on outdoor temperature, for the auxiliary heat. The installation guide should provide this and other setup option info, but I am unable to locate one online.
    crananto12's Avatar
    crananto12 Posts: 3, Reputation: 1
    New Member
     
    #5

    Dec 26, 2009, 01:35 PM
    Same here. I am contacting Honeywell and should get a response next week. Let you know how it goes.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

My folder name automatically change to .EXE [ 4 Answers ]

My folder name automatically change to .EXE

Changing tstat from Honeywell T841A1712 with Lennox T8611g [ 5 Answers ]

PLEASE need help-would like to change thermostat on my American Standard model WYC060F100AA heat pump. Current wiring on Honeywell T841A1712 thermostat is: ZONE 1 THERMOSTAT X- BLACK WIRE----COMMON R- RED WIRE-------HOT G- GREEN WIRE---FAN W2-WHITE WIRE--2ND STAGE HEAT B-BLUE...

Changing tstat from Honeywell T841A1712 with Lennox T8611g [ 2 Answers ]

PLEASE need help-would like to change thermostat on my American Standard model WYC060F100AA heat pump. Current wiring on Honeywell T841A1712 thermostat is: X- BLACK WIRE R- RED WIRE G- GREEN WIRE W2-WHTE WIRE B-BLUE WIRE E-BROWN WIRE Y-YELLOW WIRE O-ORANGE WIRE

If managers could automatically change each term in the equation of the cash conversi [ 1 Answers ]

If managers could automatically change each term in the equation of the cash conversion cycle, which of the following would be expected to provide the most benefit? A) Decrease numerator of each term by 10%. B) Decrease denominator of each term by 10%. C) Increase numerator of each term by...

Trane Gas Heat does not turn off automatically [ 1 Answers ]

I have a Trane Gas Furnace installed in 2005, Model TUD120R9V5K 4 coupled with a Trane Programmable Thermostat. Been working fine without any problem. The heat is set at 68. Last night it came on as it automatically does, but would not turn off. Finally when it got up to 78, I turned the Thermostat...


View more questions Search