Ask Experts Questions for FREE Help !
Ask
    akhilp_0074u's Avatar
    akhilp_0074u Posts: 4, Reputation: 1
    New Member
    		  
    #1

    Dec 18, 2009, 04:44 PM
    Kicker dx 200.4 amplifier will run 2 subs
    Will a kicker dx 200.4 amplifier run 2 sub woofers of 1200w - MGX
    pepsidrnkr209's Avatar
    pepsidrnkr209 Posts: 18, Reputation: 1
    New Member
    		  
    #2

    Dec 19, 2009, 01:43 PM

    It will push them for abot two min then get so hot its going to shut of and you should get a amp that can push the RMS of the speakers so you don't damage anything!
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
    		  
    #3

    Dec 19, 2009, 09:36 PM

    Give me the specs of the speakers like 4/8 ohms and max power rating.

    Also give me how many channels in AMP at what "ohms" and the smallest load it can drive, like say 2 ohms and the powers at each,
    akhilp_0074u's Avatar
    akhilp_0074u Posts: 4, Reputation: 1
    New Member
    		  
    #4

    Dec 25, 2009, 01:19 AM
    It's a 1200w sub-woofer 4 ohms
    The amp is 4 channel
    200.. 4
    200 on per channel
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
    		  
    #5

    Dec 25, 2009, 04:47 AM

    Yout amp manual is here: http://www.kicker.com/sites/default/...4in1%20a01.pdf

    Says 100 W x 2 at 4 ohms in mono mode, so yes it's OK.

    Set crossover to LO.
    akhilp_0074u's Avatar
    akhilp_0074u Posts: 4, Reputation: 1
    New Member
    		  
    #6

    Dec 29, 2009, 07:47 AM
    That means I won't get enough output right?
    akhilp_0074u's Avatar
    akhilp_0074u Posts: 4, Reputation: 1
    New Member
    		  
    #7

    Dec 29, 2009, 07:49 AM

    I tried playing it on mono
    Its getting too hot
    And den shut of for 15 min and red light appears n again starts with the green light
    copkiller's Avatar
    copkiller Posts: 1, Reputation: 1
    New Member
    		  
    #8

    Jan 8, 2012, 04:19 AM
    That's 200 watts divided by 4 you are only putting 100 watts to each sub witch will damage both your amp working it so hard and your subs starving them of power that they need
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Can I replace an ITE EQ 9483.200 amp main breaker with an EQ 9685? [ 0 Answers ]

I am replacing a 200 amp main breaker(ITE EQ 9483). The replacement breaker that I have is an( EQ 9685).Will the feed lugs of the old breaker attach to the lug stab of the new(EQ 9685) breaker?

Kicker 1947 knuckle head [ 1 Answers ]

What would cause kicker to keep engageing while motor is running

What size of cable suitable_ 40 Amps, 250'/ 200'? [ 5 Answers ]

Hello- I would like some information on wire AWG and grounding requirements with regards to generators. I set up remotely located mineral exploration camps in BC Canada- I am not an electrician... but would like to have some general information, and have an interest in electrical. Our camps...

What amp would be best for one 15" Kicker L7 Sub [ 1 Answers ]

I was thinking about getting an Alpine MRD-M1005 amp for my 15" L7 it runs at 2-ohms do you know if that would be enough?

View more questions Search