Ask Experts Questions for FREE Help !
Ask
    harry smith's Avatar
    harry smith Posts: 2, Reputation: 1
    New Member
     
    #1

    Nov 5, 2009, 07:16 AM
    Electric motors
    How do I reverse an electric motor
    harry smith's Avatar
    harry smith Posts: 2, Reputation: 1
    New Member
     
    #2

    Nov 5, 2009, 07:18 AM

    How doi reverse direction of an electric motor
    JaffarMBasha's Avatar
    JaffarMBasha Posts: 5, Reputation: 1
    New Member
     
    #3

    Nov 16, 2009, 10:40 PM

    The direction of rotation of 3-phase a.c Elctric motor can be reversed by interchanging any two phases eirher at terminals of motor or sipply mains
    SCADA ENGINEER's Avatar
    SCADA ENGINEER Posts: 1, Reputation: 1
    New Member
     
    #4

    Dec 20, 2009, 11:47 PM

    The direction of rotation of 3-phase a.c Elctric motor can be reversed by interchanging any two phases eirher at terminals of motor or sipply mains


    In addition, an example of what he said make RST change it to RTS and that will reverse the motor

    Best luck.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #5

    Dec 21, 2009, 07:34 AM

    Many Davit and lift motors have wire numbers like(for 120 Volts) connect 1 and 3 together and then hook 2 and 4 together, then hook a 5 to the 1 and 3, and hook wire number 8 to the 2 and 4 for 1 direction, then to reverse direction, reverse the 5 and 8 wires. For 240 Volts, you still reverse the 5 and 8, but now the 1,3,2 and 4 wires will be in series instead of parallel.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #6

    Dec 21, 2009, 07:53 AM

    A DC motor can be reversed by reversing the polarity.

    Then there are PSC motors, stepper motors, fan motors, ECM motors etc.

    Your question in too vague.

    Some are not reverseable.
    InfoJunkie4Life's Avatar
    InfoJunkie4Life Posts: 1,409, Reputation: 81
    Ultra Member
     
    #7

    Dec 22, 2009, 08:19 PM
    Turn it around?
    I Newton's Avatar
    I Newton Posts: 110, Reputation: 8
    Junior Member
     
    #8

    Jan 3, 2010, 05:55 AM

    A three phase motor can be done by swapping over just two of the three three phases somewhere before it gets to the motor or in the terminal box (preferably before the terminal box as it is much easier)

    Single phase motors that have a round shape attached to it (the capacitor) can be changed by swapping over the leads that go into the moot from the terminal box that are connected to the capacitor.

    This is more difficult than in the three phase.

    A single phase motor that you cannot see a capacitor on the side will 90% of the cases, NOT be able to be reversed.

    You will, in the case of a motor with no capacitor and when you pull it apart you can see small copper rings on one side of each pole, will need to be pulled apart and put back together, pointing the other way for the motor to run in the other direction.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Electric motors [ 2 Answers ]

How to build electric scooter

Electric motors [ 1 Answers ]

Will a electric motor run, if there is abreak in ithe winding , or the winding is burnt?

Electric motors [ 1 Answers ]

What is the difference between a single phase and three phase motor? And how external rotor motor works.

3 phase motors and single phase motors [ 4 Answers ]

Mike holt stated on one of his classes that in order for any eletrical equipment to work, that on one end had to be voltage and on the other side it had to have no voltage. So when the voltage goes to a three phase motor where does it go? Does it go to ground? I understand that the 3 phases are 120...

Electric motors [ 1 Answers ]

Motor has 6 poles is 3ph would like to convert to 1 ph


View more questions Search