Ask Experts Questions for FREE Help !
Ask
    pia1015's Avatar
    pia1015 Posts: 3, Reputation: 1
    New Member
     
    #1

    Jan 22, 2009, 12:34 AM
    Domestic lighting - 120v to 240v
    I'm based in Australia (240v) and have previously bought all manner of 120v US lamps, simply rewired them with local cable, plugs and using local bulbs and have used them with no problem.

    I am contemplating buying a few more US lamps but with some relatively complicated wiring (I suspect - they are pole lamps).

    How does US 120v lighting cable handle 240v - in short, is it absolutely necessary to put in new cable or can the existing US cable handle the increased voltage?

    Many thanks for any input.

    Pia
    Tev's Avatar
    Tev Posts: 232, Reputation: 20
    Full Member
     
    #2

    Jan 22, 2009, 11:58 AM

    You should check with the manufacturer but I would be very surprised if the wiring for a lamp recently manufactured in the US was rated at less than 300 volts.
    pia1015's Avatar
    pia1015 Posts: 3, Reputation: 1
    New Member
     
    #3

    Jan 22, 2009, 10:06 PM

    Thanks for the input! We're looking at vintage lighting - probably manufactured in the 50s or 60s. Any thoughts on that? Cheers/Pia
    Tev's Avatar
    Tev Posts: 232, Reputation: 20
    Full Member
     
    #4

    Jan 23, 2009, 03:13 PM

    With something that old I'd be inclined to open it up and check the wiring for any cracks or loose connections. I'd have it apart anyway so I'd update the wiring because it is unlikely the wires will have any legible markings to tell you their rating.
    pia1015's Avatar
    pia1015 Posts: 3, Reputation: 1
    New Member
     
    #5

    Jan 24, 2009, 12:32 AM

    Thank you, Tev. Your advice makes total sense and we will follow it. Cheers/Pia

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

240v to 120v [ 1 Answers ]

I have a 240 volt breaker box, need to put 20amp breaker for 120v in it. How do I put a breaker in & get 120v. If I single phase it, I only get 94 volts

240v vs 120v well pump [ 1 Answers ]

Hello guys I would like to know which is better . I have a electric well pump that can either be wired 240v or 120v but I don't know which would be more efficient. Could some one please give me some advice.:confused:

Converting 240V to 120V [ 4 Answers ]

I decided to go with a gas dryer and will be removing the 240 receptacle and replace it with 120. Can I use the heavy gauge wire already in place along with the circuit breaker, which is 50 amps or change it?:confused:

120v to 240v [ 5 Answers ]

Hello! If anybody could help me with this it would be great. I'm looking at buying a festool saw from america which runs on 120v but tools and electrical equipment in austraila run on 240v. Is there anything I can do to make it work and if so is it going to be a hassle??

240V/20Amp to 2(120V/?Amp) [ 1 Answers ]

I have a 240V line with max load 20Amp. If I split each of the hot 120V leg sharing the neutral and ground to 2 individual 120V outlet/receptacle, what would the max amp load of each? Does it sill maintain 20Amp? Or reduce by 1/2? Is there a formula to this? Thanks.


View more questions Search