Ask Experts Questions for FREE Help !
Ask
    1stephanie's Avatar
    1stephanie Posts: 1, Reputation: 1
    New Member
     
    #1

    Sep 23, 2008, 08:04 PM
    Two thermostats one gas funace
    I would like to use 2 thermostats on one gas furnace. One for the gas furnace and the other thermostat to control just the blower on same gas furnace? Then put in an out door wood boiler with hot water heat in same gas furnace. 4 wire heat cool. I have a Lennox G61MP series. Need to know how to wire the thermostats.
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #2

    Sep 23, 2008, 11:08 PM
    Just purchase a two stage heat thermostat and follow the install instructions included with the thermostat. If a difficulty pops up with the install I recommend you contact a local HVAC company to do a ON SITE survey of your situation since this type of wiring can be difficult if not impossible to explain in this venue since so many different control and wiring combinations are possible. Better to be safe than sorry.
    eschuen's Avatar
    eschuen Posts: 62, Reputation: 6
    Junior Member
     
    #3

    Sep 26, 2008, 05:22 PM
    I'm not sure if my schematic downloaded. If it did you need to be careful not to run both t-stats at the same time. You have a 2 stage system right now and I can't guarantee if they both try to run some major damage won't happen. This is a very simply system I drew. I've installed some systems similar to what you want to do. I can tell you up front depending on what your burning (the temp of the water) it can get really hot . That limit switch will open and is suppose to shut down the system and won't be able to. It would take a solenoid valve to give you complete control of your system and depending on what type of boiler you have maybe a few more options. I just seen my file is to large to download. You can write me at "[email protected]" and I'll mail it to you
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #4

    Sep 26, 2008, 05:29 PM
    It does not seem your drawing downloaded to the board. Try again

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Keepright funace or American Standard Furnace [ 1 Answers ]

I am trying to decide which furnace I should replace my existing furnace with a Keepright Furnace or American Standard Furnace? Both are there Higher End Furnaces. Please Advise

Aircondition not running and funace not on [ 9 Answers ]

Hi All, I came home today and the I discovered the air conditioner is not working. The symptoms are that the furnace indicator lights are not on which might indicate the furnace is not getting power. The blower does not turn on when the thermostat is sending a signal. Also, the outdoor AC unit...

Current Limit for funace accessories [ 1 Answers ]

I've got an Air Ease furnace Mfg by Lennox. P/N G1D91Au. I've already connected a humidifier to the 120V HUM terminals on the blower control board. Also, I would like to add a couple of duct boost fans and wire to the blower control board. I could use the 120 V terminals for the Electronic Air...

Funace stops kicking on [ 3 Answers ]

Hi I am having problems with my furnace. It is a Pulse and is only about 7 or 8 years old. The problem is, is that it works for a while and then it will NOT kick on again. If you turn the power off at the thermostate it will come back on and will work again anywhere from 4 to 10 hours before it...

Goodman gas funace pressure switch problem [ 9 Answers ]

I have a Goodman 93% efficient furnace that short cycles the gas burners. It cycles the vent on, starts the igniter, fires the burners and kicks on the blower but the burners only stay on for a short time ( less than 30 seconds). The led on the circuit board gives me 3 flashes indicating " pressure...


View more questions Search