 |
|
|
 |
New Member
|
|
Jul 25, 2008, 08:56 AM
|
|
Shutoff valve replacement for bathroom sinks and toilet
I am replacing my old shutoff valves under my bathroom sink and toilet. How do you go about getting them off when they are soldered on? I know they need to be sweat off , but not familiar with the technique. Please help.
|
|
 |
Home Improvement & Construction Expert
|
|
Jul 25, 2008, 09:22 AM
|
|
Normally you cut them off. Most of the time theses are compression fit. Are you sure they are soldered.
|
|
 |
New Member
|
|
Jul 25, 2008, 09:38 AM
|
|
Thanks for your quick response. Yes the vales are soldered on. The house was built in 1978 and they are original. So I just need to cut them off and can use ones with compression fittings? Sounds easy enough. Thanks
|
|
 |
Ultra Member
|
|
Jul 25, 2008, 01:29 PM
|
|
If you have room to cut it, and install the compression angle valve see the picture, good luck.
John
|
|
 |
Plumbing Expert
|
|
Jul 25, 2008, 06:51 PM
|
|
I have seen these valves in Home Depot. If it sticks out a bit, cut it off. Otherwise, you have to take a torch, heat it up and pull old valve away from the pipe. Now, you can either use compression type valve or solder on 1/2" Male Adapter and screw on regular 1/2" MIP valve.
You may have a problem with compression valve since the pipe will be "dirty" from previous installation. I think the second option is better way to go.
Also, I have already seen "SharkBite" fitting type angle stop valves in Home Depot. No soldering. Just push it on to the pipe and you are ready to reconnect your water supply.
|
|
 |
Ultra Member
|
|
Jul 25, 2008, 07:47 PM
|
|
I would suggest to use the compression type of valve if it is possible, Thanks.
John
|
|
 |
Eternal Plumber
|
|
Jul 26, 2008, 06:49 AM
|
|
I agree with John,
Asking the home owner to solder on a male threaded adapter is just piling on more work. If, by "dirty" Milo means solder left on the pipe simply heating the pipe and wiping the solder off will allow you to install a compression or a Sharkbite angle stop. Good luck, Tom
|
|
 |
Ultra Member
|
|
Jul 27, 2008, 09:25 AM
|
|
Tom Or the shrkbite angle stop out yet where can I find one?
I looked every where can't locate it, Thanks
|
|
 |
Eternal Plumber
|
|
Jul 27, 2008, 09:50 AM
|
|
 Originally Posted by afaroo
Tom Or the shrkbite angle stop out yet where can I find one?
I looked every where can't locate it, Thanks
Our Home Depot carries them. But if you can't locate them locally then I'll give you a link from the internet. Regards, Tom
|
|
 |
Plumbing Expert
|
|
Jul 27, 2008, 10:05 AM
|
|
 Originally Posted by afaroo
Tom Or the shrkbite angle stop out yet where can I find one?
I looked every where can't locate it, Thanks
Our Home Depot sells them too. They are 1/2" Comp x 3/8" Comp in PC. So far, 3/8" Comp only.
|
|
 |
Ultra Member
|
|
Jul 27, 2008, 12:23 PM
|
|
Thanks Tom & Milo, I went to two Home depots didn't find the Sharkbite angle S/O valves every thing else was there but the stop, Tom I would appreciate if you send me the link, Milo yesterday I sent you a privet message I didn't get respond, Thanks.
Best Regards,
John
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Replacing shutoff valve under bathroom sink
[ 14 Answers ]
I just replaced the bathroom faucet but ran into a small snag while doing it. The old semi-flexible line from the cold shut off was too short to reach so I ended up attaching the hot supply line to the "cold" faucet and attached the cold supply line to the "hot" faucet and then just swapped the...
Old toilet 2 incoming water lines, no shutoff valve.
[ 1 Answers ]
My first order of business after moving into a new house this weekend was to replace the toilet. It's an older house and there are 2 water lines feeding the toilet for a supply.
There is no flexible supply line going to the toilet. It seems the only way to put in the new one without problems...
Toilet Water Supply Shutoff Valve problems
[ 1 Answers ]
Hello,
My problem is this; When I turn the toilet water supply valve I don't hear any water flow sound anymore, so the only way we can flush the toilet is to fill up a bucket with water and pour it down. Before we had the same problem but what we would have to do is turn on the faucet to the tub...
View more questions
Search
|