Ask Me Help Desk

Ask Me Help Desk (https://www.askmehelpdesk.com/forum.php)
-   Plumbing (https://www.askmehelpdesk.com/forumdisplay.php?f=259)
-   -   Shutoff valve replacement for bathroom sinks and toilet (https://www.askmehelpdesk.com/showthread.php?t=241528)

  • Jul 25, 2008, 08:56 AM
    carmenuche
    Shutoff valve replacement for bathroom sinks and toilet
    I am replacing my old shutoff valves under my bathroom sink and toilet. How do you go about getting them off when they are soldered on? I know they need to be sweat off , but not familiar with the technique. Please help.
  • Jul 25, 2008, 09:22 AM
    hkstroud
    Normally you cut them off. Most of the time theses are compression fit. Are you sure they are soldered.
  • Jul 25, 2008, 09:38 AM
    carmenuche
    Thanks for your quick response. Yes the vales are soldered on. The house was built in 1978 and they are original. So I just need to cut them off and can use ones with compression fittings? Sounds easy enough. Thanks
  • Jul 25, 2008, 01:29 PM
    afaroo
    1 Attachment(s)
    If you have room to cut it, and install the compression angle valve see the picture, good luck.

    John
  • Jul 25, 2008, 06:51 PM
    Milo Dolezal
    I have seen these valves in Home Depot. If it sticks out a bit, cut it off. Otherwise, you have to take a torch, heat it up and pull old valve away from the pipe. Now, you can either use compression type valve or solder on 1/2" Male Adapter and screw on regular 1/2" MIP valve.

    You may have a problem with compression valve since the pipe will be "dirty" from previous installation. I think the second option is better way to go.

    Also, I have already seen "SharkBite" fitting type angle stop valves in Home Depot. No soldering. Just push it on to the pipe and you are ready to reconnect your water supply.
  • Jul 25, 2008, 07:47 PM
    afaroo
    I would suggest to use the compression type of valve if it is possible, Thanks.

    John
  • Jul 26, 2008, 06:49 AM
    speedball1
    I agree with John,
    Asking the home owner to solder on a male threaded adapter is just piling on more work. If, by "dirty" Milo means solder left on the pipe simply heating the pipe and wiping the solder off will allow you to install a compression or a Sharkbite angle stop. Good luck, Tom
  • Jul 27, 2008, 09:25 AM
    afaroo
    Tom Or the shrkbite angle stop out yet where can I find one?
    I looked every where can't locate it, Thanks
  • Jul 27, 2008, 09:50 AM
    speedball1
    Quote:

    Originally Posted by afaroo
    Tom Or the shrkbite angle stop out yet where can I find one?
    I looked every where can't locate it, Thanks

    Our Home Depot carries them. But if you can't locate them locally then I'll give you a link from the internet. Regards, Tom
  • Jul 27, 2008, 10:05 AM
    Milo Dolezal
    Quote:

    Originally Posted by afaroo
    Tom Or the shrkbite angle stop out yet where can I find one?
    I looked every where can't locate it, Thanks

    Our Home Depot sells them too. They are 1/2" Comp x 3/8" Comp in PC. So far, 3/8" Comp only.
  • Jul 27, 2008, 12:23 PM
    afaroo
    Thanks Tom & Milo, I went to two Home depots didn't find the Sharkbite angle S/O valves every thing else was there but the stop, Tom I would appreciate if you send me the link, Milo yesterday I sent you a privet message I didn't get respond, Thanks.

    Best Regards,
    John

  • All times are GMT -7. The time now is 08:55 AM.