I have a hunter Jackson Square ceiling fan on a wall remote kit that came with the unit. It randomly powers on and off and changes speeds. I have changed the frequency on the remote and receiver multiple times and it still does this. The house was prewired for this when I purchased the house so I "guess" that all the wiring is good. I have good voltage coming through and no shorts in the wire. This fan has no pull chains and no manual reverse switch so I need a remote that is capable of reversing fan direction and have been unable to locate a replacement that can do that. Any help would be appreciated.

Normally I would expect changing frequencies to fix it. Someone else had the same problem, here was their solution:

Harbor Breeze - receiver bad?

Quote:

---

Originally Posted by ceilingfanrepair

Normally I would expect changing frequencies to fix it. Someone else had the same problem, here was their solution:

Harbor Breeze - receiver bad?

---

So I got Hunter to send me a new receiver and have gone through a few more channels and am still having the same trouble. Is there a hardwire solution out there so I don't have to use a remote unit? I pretty much don't care about reverse anymore. I also attempted the wrapping in tape solution and I even cut a few inches off the antenna. The fan is a Hunter Jackson Square model# 21403. I have the manual in pdf format if that helps at all.

Remove batteries from transmitter, Or move way out of range.
Buttons may be sticking or intermittent. Replace transmitter if so.

Quote:

---

Originally Posted by Stratmando

Remove batteries from transmitter, Or move way out of range.
Buttons may be sticking or intermittent. Replace transmitter if so.

---

I left both transmitters with no battery last night and it still happened.

Do you have More fans in the house like this one.
Were all the houses nearby built about same time or same contractor.
Do not use default settings.
Don't use codes like, all on, all off, on off on off on off.
I would suspect neighbors Fan Remote.

I checked with the neighbors on both sides and both say they do not have any remote fans. I also cut my antenna down to about 1" in length thinking this might help. It still seems to get a signal from about 30' away but I am leery about cutting it any shorter. I'm going to try changing the channel a few more times but i have been through at least 10 of them already. My other fans in the house are all a different brand and on different channels. Would any type of electrical problem cause the reciever to think it needed to turn on? Surge? I've heard the term "dirty power".

If it happens consistently enough, Turn off different electronics, electrical devices, and electronic devices. Wireless router, IR extenders, Alarm wireless devices. Anything
That generates a signal, does not have to be wireless device or appliance.
What type of electronics do you have? Do you have an antenna or cable amp? If you are
Confident in Electrical, Place that circuit on opposite phase. If on circuit that shares neutral.
Switch places with that, to keep from overloading Neutral. There is a chance is is on the line and not on air. Good Luck, Let Me Know.

Stratmando is correct, it doesn't require another fan to create interference, any RF device will do it. You can also try wiring to a different circuit and/or phase in case there is noise that is interfering.

I had a haunted fan that turned out to be controlled by a neighbor a block away. He was using an X10 control device that send signals through the house current and anyone else on that transformer.

Never heard of that before, but it doesn't surprise me! Damn kids with their loud music and X10 devices and pants worn at or below the waist!

LOL the X10 is a remote device that can be hooked up to control lights, fans, furnace, etc via a remote or your telephone. But I do agree about those kids.

I'm familiar with X10. And I probably AM one of those kids :)

Ouch, you pulled my leg so hard it hurts.

I was saying I hadn't heard of X10 affecting a ceiling fan, but I do know what it is. I used it on my Christmas tree one year.

I tried using it on my furnace but too many others in our lake area used them too. I switched to something called TalkingThermostat and that did the trick. Interseted in buying my slightly used X10?

Well thank you all for the advice. After much arguing with Hunter they are sending me a brand new fan that is exactly the same except it is a hard wired version. Now I'll be able to install my own speed control wall unit without having to deal with this problem "crosses fingers"

If it is X10 type(Power Line Carrier) Look at houses on same secondary side of transformer.(maybe 6 or 8 houses total) signal will be trapped by windings
of transformer(act like a choke)on houses further away.
X10 makes a whole house filter, to block PLC signal from getting in.
The Wireless innercomms that are PLC. You and neighbor on same transformer con communicate if you wish.