Ask Experts Questions for FREE Help !
Ask
    Racer Duck's Avatar
    Racer Duck Posts: 2, Reputation: 1
    New Member
     
    #1

    May 5, 2007, 01:27 PM
    Briggs 22HP Won't Start
    I have a Briggs 22hp (model 407777) on a Troy-Bilt (MTD) frame.. it's about 5 years old.

    I recently had a problem with a bad battery which, when replaced everything worked fine.. for about a month. Then the solenoid stuck ON causing the starter to "click" every time the key was turned on. The battery has to be removed on this model to gain access to the solenoid (under the seat), which was removed and a new solenoid installed.. but one wire was not returned to the proper place, a green one that should have gone to the battery ground was instead connected to the open battery terminal on the solenoid. When the key was turned on and the starter engaged, smoke came from the "Y" in the wires going to the lugs on the 2 coils. It appears there was a fuseable link or a diode at the "Y".. not having a wiring diagram, I soldered the 3 leads together. Though everything appears to work, I get no spark at the plugs.

    Any help getting this thing going will be much appreciated as I have 3 acres of knee high grass that needs a "trim"...
    Racer Duck's Avatar
    Racer Duck Posts: 2, Reputation: 1
    New Member
     
    #2

    May 5, 2007, 05:57 PM
    Found the problem.

    Because I soldered the wires together that go to the coils (kill switch circuit), it didn't matter which cyl was firing 'cause the other coil was providing the ground (kill signal) so they never fired. When I removed the kill wires, the engine started and ran fine.

    Evidently there were diodes inline that prevented the "cross kill" from happening. Now, I need to find a p/n for the diodes...

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

14.5 Briggs won't start [ 1 Answers ]

The engine ran fine last season and haven't tried to start it since but had to replace flywheel and starter gear to start this year. After replacing the gears and installing a new spark plug and charging the battery the engine spins freely and backfires but doesn't start. I don't know much about...

22hp v-twin B&S won't start [ 2 Answers ]

My v-twin 22 hp B&S mower won't start. If I put gas in carb it will run till that gas burns up. I am not getting any fuel in fuel filter. The mower is a poulan. I was woundering what could be the problem is there a fuel pump on this mower ? Thanks

Briggs Vanguard will not start [ 14 Answers ]

Briggs Vanguard, 15 hp OHV Model 280777 Type 0112.01 Code 94121154A Simplicity Brood Moor... The oil was checked and gas was checked prior to starting, the mower had been sitting for 4 to 6 weeks due to cold weather. I decided to started it and ran it at normal start speed until It warmed up....

16.5 Briggs in MTD will not start [ 5 Answers ]

I have a 16.5 ovh Briggs in an MTD. The mower started and ran fine the last few mowings. However, now it will not fire. The starter will turn the motor for a few seconds and then it will "bog" down. I can turn the motor by hand past the "hard" part of the engine cycle and the starter will turn the...

Briggs 16.5 won't start [ 1 Answers ]

I have a B/S 16.5 OHV Twin (Commercial model). Generally speaking it starts as soon as I hit the key. Today when shutting it down it backfired twice (two different occasions) but started normally. When I went to start it to put it in the shed no luck. Doesn't sputter or backfire. Changed the...


View more questions Search