Ask Experts Questions for FREE Help !
Ask
    Artwen's Avatar
    Artwen Posts: 4, Reputation: 1
    New Member
     
    #1

    Apr 24, 2007, 11:22 AM
    Corrosion? Of Plastic Stems of Water Shut-off Valves
    In a condominium constructed about 12-15 years ago in Henderson, NV, I discovered 6 out of 8 under-sink water shut-off valves to have badly corroded valve stems, if that term can be legitimately applied to plastic. The "corrosion" was so bad that one valve had failed causing a flood. Since 75% of 8 identical valves exhibited very bad signs of this "corrosion", it appears to be related to a chemical attack on the plastic caused by the water and possibly other nearby materials in the valve. The valve bodies were brass. The valve stems that were badly attacked were of a gray plastic. The only identification on the valves were the words "BOB" and "USA" molded into the clear plastic valve handles. What does this problem stem from and who made these valves? I have attached a photo of the worst example that failed.
    Attached Images
  1. File Type: pdf Under-Sink Shut-off Valve that Failed.pdf (129.7 KB, 334 views)
  2. hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #2

    Apr 24, 2007, 04:55 PM
    The name or company symbol in on the handle. There is now warranty or liability on a 12/15 year old valve. Just go to Home depot/lowes and get new ones. Replace them all.
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
     
    #3

    Apr 24, 2007, 06:11 PM
    A strange, cheap looking thing. That damaged stem looks to me more like heat than chemical damage. If it doesn't mean adding too many extra fittings, I would put in ball valves. Much easier to work with, less likely to leak, and when shut off, stop all the water from flowing.
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #4

    Apr 24, 2007, 06:26 PM
    ((I wanted to know what caused the problem. No valve of this type should expire so quickly!)

    No one here will be able to tell you exactly what happened to the valve. That is why I said to look at the top of the valve handle to see if the manufactures name was there. That way you could call them and lodge a complaint.

    A valve should never go bad but they are replaced all the time. I know of no reason a plastic valve should look like that unless someone was soldering a pipe or something above the valve and the hot solder dripped and melted it.
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
     
    #5

    Apr 24, 2007, 07:09 PM
    The whole thing is really strange. Was there once a nut on the threads where the valve stem comes out? Will the valve stem and internals screw right out? Even boiling water would hardly damage most plastics that would be used in such an application. Solder was a good suggestion, but I find it unlikely solder would have dripped on all of them. Have you compared yours to others in the condo?

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Can one shut off water main valve but leave gas hot water tank on? [ 4 Answers ]

I would like to know if I go away for two days and shut my main water shutoff valve can I leave my gas hot water tank on. I saw two answers To a similar question and one answer said you can leave it on and the other Said you had to shut it off. I am confused now as to whether I can leave the gas...

Vanity water supply valves leak [ 2 Answers ]

In replacing the hot and cold water supply valves under the sink I have a slow leak. The end of the copper pipe has a ridge on it with a nut receptacle behind it where I am screwing the new valve into. I have used tape and grease with no luck. Any suggestions?

Installed new bathtub valve stems now "no cold water" [ 5 Answers ]

I have just replaced both hot and cold valve stems in bathtub. I did them exactly the same and now I can't get the cold water to come out. What can I try to do to fix this problem. Someone said I should have the valve open when installing? I am desperate and exhausted please help!! :(

Access to shut off valves [ 1 Answers ]

Does anyone know if there is a code in sarasota fl that says you must have access to shut off valves in your tubs and if so what is that code and where can I get a copy. Thank you[ Manny

Leaky Shut off valves [ 3 Answers ]

Hi, I live in the Northeast and for the first time this past winter, I actually used the shutoff valves that lead to my outside water spigots. Now that I've turned them back on, they are leaking whenever the water line is open. I noticed they have nuts on the front... was I supposed to...


View more questions Search