 |
|
|
 |
New Member
|
|
Apr 1, 2014, 04:48 PM
|
|
1995 F350 7.3 L power stroke diesel want start not even with starter fluid
I have a 1995 F-350 7.3 L power stroke diesel want start no even with starter fluid
|
|
 |
Uber Member
|
|
Apr 1, 2014, 05:00 PM
|
|
Starter fluid is a huge no-no for most diesels. Causes head gaskets to blow out from the ultra high cylinder pressure spikes since you are already starting out with 18-1 to 22-1 compressiuon ratios.
DO you have compression? Are you getting fuel? Lots of unknown things that could cause a no-start... we have no idea what the status of any of them are.
|
|
 |
Uber Member
|
|
Apr 2, 2014, 08:17 AM
|
|
Basic Diesel Engine Troubleshooting
The generic steps below can help solve many diesel engine starting problems.
1. Remove and fully charge both batteries, disconnecting the negative batterycable first. Diesels require strong batteries, particularly in winter.
2. Clean battery terminals and cables--apply dielectric grease.
3. Check all under hood and under dash fuses with a test light or multimeter:
. Test Light. Turn ignition switch to ON (Position II), connect alligator clipto vehicle ground, and touch the probe to each test point on the fuse. The testlight must come on at each test point on the fuse; otherwise, the fuse is bad.
. Multimeter. Set multimeter to DCV, turn ignition switch to ON (Position II),touch the black test lead to ground, and touch the red test lead, in turn, toeach test point on the fuse. The meter should record 12+ volts. Voltage must berecorded at each test point on the fuse; otherwise, the fuse is bad.
An alternative method, which is very fast, is to set your multi-meter toaudible ohms, DISCONNECT THE NEGATIVE BATTERY TERMINAL (or you could blow thefuse in the multi-meter), and touch the red and black test leads to the testpoints on each fuse. When you hear the meter buzz, you know the fuse is good.This is my favorite method. If your meter doesn't have audible ohms, but itdoes have ohms, you can still use this method--just read the meter instead. Thealternative methods perform a continuity test on the fuse. Just remember tode-energize the circuits, by disconnecting the negative battery terminal, andrecord any radio activation codes first.
These methods allow you to accurately and quickly check all under hood andunder dash fuses in several minutes, even in dark, cramped locations. Theyeliminate the possibility of removing and replacing the fuse in the wrong slot.Should a fuse test bad, use the fuse puller, provided in the under dashfuse/relay box, to remove it.
4. Check for Diagnostic Trouble Codes (DTCs). Attach code reader or scan toolto the Data Link Connector (under the dash), turn ignition switch to ON(Position II), and read codes. Use a code reader or scan tool to clear codes,once repairs are made.
5. Ensure engine oil is full and that the oil and filter have been recentlychanged. On Ford PSDs, I recommend only using Motorcraft oil filters and fuelfilters. Alternative filters can adversely affect fuel pressure.
6. Verify oil pressure on Ford PSDs with a known good mechanical gauge. Oilpressure may be too low. The cutoff will shut the engine down when the oilpressure is too low. PSDs use the Hydraulic Electronic Unit Injection (HEUI)System, so it completely relies on the oil level and condition of the oil tofire the injectors. Running the oil level low or too long can cause unusualproblems.
As the name implies, the HEUI injection system uses hydraulic energy to actuateunit injectors. A PSD has two oil pumps--a low pressure lubrication pump, located near or in the front engine cover below the water pump, and a high pressure hydraulic pump, located at the front of the engine V, underneath the fuel filter assembly. If the problem persists, focus on the High Pressure OilPump. If the Injector Control Pressure (ICP) is lower than expected (engine cranking), it is usually caused by low injection oil pressure or regulator (IPR) valve. High pressure oil is used to pressurize and inject fuel into the cylinders--each injector is essentially its own injection pump. The IPR is aby-pass valve that controls the high oil pressure, depending on demand. The ICPSensor monitors the oil pressure in the LH head. Check for oil in the upperreservoir--it should be within one inch of the top (add as necessary). Verifythat the correct oil is being used and that it has not thinned out. For no-start concerns, check ICP Sensor readings with a scan tool or pressure gauge.
On diesel engines that will not restart, after they are warmed up, it's often a sign of a tired fuel pump. As they heat soak, inside pump head clearances increase and it will no longer develop sufficient fuel pressure at cranking speed. While it's running, fuel helps cool the pump by carrying the heat away.
|
|
 |
Uber Member
|
|
Apr 2, 2014, 08:24 AM
|
|
7. Check glow plugs, which are used to heat the fuel:
. Testing. Use an ohm (Ω) meter to check for continuity, which will tell you if the glow plug is shot, has continuity, or is worn. Ohm out each plug through the harness. Good glow plugs will have a resistance between 0.6 and 2 Ω. If you get infinite resistance on any plug, it is either bad or the connector under the valve cover is loose.
. Removal and installation. With the engine "stone cold," disconnect batteries, remove valve cover, disconnect glow plug connector, remove glow plug with a 10 mm deep socket, install new glow plug (torque to 13 ft.-lbs.), and reattach connector. After finishing the remaining 3 glow plugs on that bank, clean valve cover, install new gasket, and reinstall valve cover (torque to 97in.-lbs.). Do the same thing for the other bank of glow plugs and reconnect batteries. Not a difficult job--should take several hours.
8. Check glow plug relay (GPR). Ensure the engine is cold, so that the PCM will tell the GPR to turn on. If the engine is hot, you won't have as much time to check. Locate the GPR, which is often behind the fuel filter on top of the engine, slightly toward the passenger side of the valley on PSDs. There may be two relays there. If so, the rear relay is the GPR. It should have two fairly large wires (Yellow and Brown) connected to one of the large posts. With multi-meter set to DC volts, or 15V range if not auto-ranging, clip the positive (Red) lead to the output terminal (with yellow and brown wires connected), and the negative (Black) lead to ground. Turn the ignition switch to ON. If the GPR isgood, it should click, and you should see 11 volts or so on the meter; then, depending on temperature, it will click off up to 2 minutes later. Do this a couple of times, to ensure it consistently makes the connection. If there is no voltage with this test, confirm by retesting as follows. Remove the two small wires from the smaller two of the four GPR terminals. With jumper wires, apply voltage from the battery across the two small terminals. If the voltmeter now reads voltage on the output terminal, the GPR is good and the problem is in the PCM circuit that tells the GPR to activate.
9. Check block heater, which is used to heat the engine.
10. Check fuel injectors. Take the valve cover off and look at each injector's exhaust, while the engine is running. Each time an injector fires, you should see oil exhausting from it. If you see oil coming out, then the injector is good. When replacing a bad injector, cut fuel, remove the glow plug, and crank the engine to get any fuel and oil out of the cylinder. If you don't, you could hydro-lock and bend a rod.
11. Purge fuel filter or fuel separator of water. Do this at least monthly--daily, if necessary. Water can be a big problem with diesels, particularly in the winter. Replace fuel filter(s) every 15,000 miles.
12. Check turbo--it may be coking up or turbine blades may be bent. Only use full-synthetic HDDO with a turbo. With conventional diesel engine oil, it's only a matter of time until the turbo fails.
13. Check/replace air filter. Diesels require lots of air--restricted airfilters can bend turbine blades. Check every 5,000 miles, replacing it as needed.
14. Assess fuel quality. In cold weather, many diesel owners have problems withthe new ultra low sulfur diesel fuel (ULSD). The problem comes from the refining process used to attain the ultra low sulfur ratio. It affects the naturally occurring wax and can cause the fuel to gel more readily in cold temperatures. Gelled fuel clogs the fuel filter and starves the engine, causing it to stop. Adding diesel fuel additive often helps. Diesel fuel additives, such as Amsoil's, and ultraclean kerosene added to the fuel help prevent this problem.
15. Check compression. A diesel engine that "cranks normally but won'tstart," regardless of the outside temperature, either has low compression or a fuel delivery problem. If compression is okay, a) check the fuel gauge (to ensure there's plenty of fuel), b) fuel filters, and c) fuel lines for obstructions.
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
1995 F350 7.3 turbo diesel no power!
[ 2 Answers ]
I just bought a 1995 f350 7.3 liter turbo diesel with 5sp man trans. 108k miles. When I test drove it it was about 28 degrees outside and it ran great, started right up (cold) and the turbo was clearly working. Now it seems to bog down at about 2200-2500 RPM in every gear and putting the pedal to...
Ford F250 Power Stroke diesel won't start after running
[ 1 Answers ]
I have a 2005 f250 6.0 power stroke with 100,000 miles and until now have not had many problems. Turbo clamp blew off replaced clamp and turbo
Problem:
After I run the truck no matter how far or long it will not start until it sits for a few hours or I use stating fluid and sometimes that...
97 f350 power stroke turbo diesel skipping
[ 0 Answers ]
hi I'm jimm and my problrm is interesting we put a 97 ford f350 turbo diesel 4x4 its not locked in four wheel but when you make a right hand turn the truck bucks and skipsm like its not getting gas when you make a left turn its fine but skips sometimes when you first strart out. I'm not sure if...
View more questions
Search
|