Ask Experts Questions for FREE Help !
Ask
    Al Berstler's Avatar
    Al Berstler Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Mar 12, 2007, 11:10 AM
    Installing heatpump or AC
    Hi I'm remodeling a house built in '32, with an addition in the 40s or 50s. The house is about 1200sq ft (800 sq ft w 9' ceilings, 400 sq ft with 8'ft ceilings) with a 1/2 basement where the heater (oil) water heater, circuit panel etc. At present there is no AC in this house, although the air handler has an evaporator in it. The oil furnace appears fairly new and was replaced prior to taking possession of the house. The heater has duct work 6 outlets and 4 returns with a single larger return above the air handler in the basement. All ducts are about 6" diameter.

    The simplistic side tells me I should be able to add central AC (I suspect a 2ton unit would suffice for this size house) by installing a compressor/condenser outside, running the freon lines to the evaporator.

    My question(s) is: Is there a way to converting this to a heat pump, and keeping the oil furnace as a backup (or alternate heat source when the weather is very cold)?

    Is there a downside / upside to this?

    Also, is there anyone that has experience using a geothermal heat pump with an injection well?

    Thanks in advance to anyone/everyone's opinion.

    Al
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Mar 12, 2007, 03:34 PM
    You can install a heat pump. The system will be called a dual fuel system. I recommend a pro look over your situation with the house for proper sizing and insulation/window factors. You should reall have a manual J done on the structure so you are not guessing as for size ETC.
    Al Berstler's Avatar
    Al Berstler Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Mar 13, 2007, 07:17 AM
    hvac1000, Thanks for the information and advice.
    My efforts will be to get the permits, run the electrical and the plumbing. I plan on contacting a pro, when getting to the details (sizing, location etc.) and to contract the hookup. I just want to make sure I ask the right questions and am able to explain what I want so I don't waste anyone's time and money.
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
    		  
    #4

    Mar 13, 2007, 02:57 PM
    As far as I know, you should be able to instal a heat pump or ad AC. Big difference is that a heap pump has reversing valves to direct the flow of liquid and vapor phases of the freon. The evaporator would also need to be capable of working as a condenser in the heating mode. What you already have may not do. You might see the heat pump section of the sticky at the top of the forum.

    Most heat pump systems are set up to call on another source of heat below the temperatures where the heat pump is most efficient.
    Dromedarius's Avatar
    Dromedarius Posts: 10, Reputation: 2
    New Member
    		  
    #5

    Mar 14, 2007, 10:54 AM
    Geothermal heat pumps are very expensive. Even though they really slash your heating and cooling costs it would take forever to recoup those expenses. Also, is this in reference to THIS house (built in 1932)? If so, there are a lot of other options at your disposal to obtaining greater efficiency which would be a lot less expensive (adding insulation, sealing doors and windows, insulating hot water pipes, etc. etc.). Even one of the more expensive options, installing new windows, would probably be significantly cheaper and increase the value of your home. I would only go the geothermal route if they became significantly cheaper and I were building a new home in which I planned to live forever. :p
    NorthernHeat's Avatar
    NorthernHeat Posts: 1,455, Reputation: 132
    Ultra Member
    		  
    #6

    Mar 14, 2007, 03:06 PM
    Airflow is very critical in a heat pump, ductwork, not the size of the house will be the priority. It can be done though. If you live in a very cold climate the cost of the heat pump may not be offset by the efficiency savings. Around here oil is still at a reasonable cost per BTU, at least better than LP.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Heatpump thermostat [ 1 Answers ]

I have a goodman heatpump with a janitrol 1890 thermostat it has never switched the aux heat on .When the temp gets too cold for heat pump to make heat .I have to turn emergency heat on myself .Book says model1860 thermostat is what should be installed is this my problem if so a new thermostat...

Goodman Heatpump Blower Intermittent ON [ 1 Answers ]

I have a Goodman (Janitrol) Model # CPE36-1AB heatpump cooling AC system about 14 years old (new in 1992). The outside unit comes on in heat mode but the blower sometimes doesn't come on in the air handler . I can feel the insulated pipes leading into the evaporator are hot in the air handler and...

Runaway heatpump [ 5 Answers ]

I have a 1400sq foot 2 story home built in 2005 with a single heat pump. The thermostat is located on the first floor. During the winter the heat will run and run to try to maintain the temperature on the first floor but the second floor will bake. For example, the first floor may be set to 70 but...

Heatpump blower cycles on off [ 1 Answers ]

The heatpump works but the blower has problems. When the fan is put to "On", or when the system is initiated by the thermostat, the blower sometimes will try to start, but cycles on/off. I can hear the relay clicking. When the system does operate correctly the problem will eventually re-occur....

View more questions Search