Ask Experts Questions for FREE Help !
Ask
    dennis3824's Avatar
    dennis3824 Posts: 3, Reputation: 1
    New Member
     
    #1

    May 9, 2012, 09:56 AM
    Whirlpool gas dryer won't turn off, no heat
    I have an estate model tgdx640jq2 dryer thatwont heat up and then won't turn off.
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
     
    #2

    May 10, 2012, 08:55 AM
    You have two problems: something is open in the heater circuit, probably the thermal cut-off because the dryer got clogged with dirt and no one took it apart and cleaned it; and, you most likely have a bad timer where a set of contacts that sends power to motor are welded together.
    You are going to have to take it apart to clean it and find the thermal cut-off and test it with a meter and you will have to test the timer contacts. You will need a multimeter to track down these problems. Here is a book to help: http://dl.dropbox.com/u/8010163/Whir...e%20Manual.pdf
    And: http://dl.dropbox.com/u/8010163/Whir...e%20Manual.pdf
    And: http://dl.dropbox.com/u/8010163/Kenm...%20Manuals.zip
    I hope these help. When you remove the rear cover of the control panel where the timer is located you will see a tech sheet. If you will scan this to a jpg file and send it to [email protected] I will see what I can do to help you. The manuals I posted for download should be close to yours as they are all pretty much the same except for minor differences.
    dennis3824's Avatar
    dennis3824 Posts: 3, Reputation: 1
    New Member
     
    #3

    May 11, 2012, 04:55 AM
    Quote Originally Posted by drtom4444 View Post
    You have two problems: something is open in the heater circuit, probably the thermal cut-off because the dryer got clogged with dirt and no one took it apart and cleaned it; and, you most likely have a bad timer where a set of contacts that sends power to motor are welded together.
    You are going to have to take it apart to clean it and find the thermal cut-off and test it with a meter and you will have to test the timer contacts. You will need a multimeter to track down these problems. Here is a book to help: http://dl.dropbox.com/u/8010163/Whir...e%20Manual.pdf
    and: http://dl.dropbox.com/u/8010163/Whir...e%20Manual.pdf
    and: http://dl.dropbox.com/u/8010163/Kenm...%20Manuals.zip
    I hope these help. When you remove the rear cover of the control panel where the timer is located you will see a tech sheet. If you will scan this to a jpg file and send it to [email protected] I will see what I can do to help you. The manuals I posted for download should be close to yours as they are all pretty much the same except for minor differences.
    Sent legend via regular email. Will be looking at dryer on Friday. Hope this legend helps.
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
     
    #4

    May 11, 2012, 06:17 AM
    Looking at the schematic I see where the timer is the only thing that can keep the dryer running past when it should turn off, so you need a new timer. Secondly, There is a non-resettable thermal fuse with two blue wires going to it that can be the cause of the gas not coming on, but you will have to test it with an ohm meter. There are also some other things on the gas valve and assembly that you can test in case the fuse is good, but I really doubt you will have a problem with the other parts, however, the readings and test points are clearly labeled on the schematic near the bottom. You should test the solenoids because if they are bad, or the main one, nothing will fire. One is 1220 ohms and the other is 560 ohms. Just unplug one wire when testing something.

    You also need to totally tear it down and scrape out and wash all of the parts except the motor, which you vacuum out. You can go to YouTube to see videos on how to take it apart, but do a very good job or it will fail again quickly. Dirt makes the fuse blow. I would get a new belt and change it while you have it apart and get some white lithium grease and grease any bearings you find. You need to clean out a drier every two years, at least, according to the manual. All sensors work together by comparing temperature, so all need to be cleaned. You just unplug the wires from the sensors and remove ductwork that they are attached on and clean the entire thing with soap and water. Make sure you go all through the dryer and get all parts like the blower fan and housing, vacuum out motor well and clean exhaust. Mark all wires you unplug so you know where they go. This is an easier job than you would think. My sister does hers at least once a year since she has five children and the dryer gets a lot of use. This is an easier job than you would think. See: Dryer vent cleaning prevents fires - YouTube and: Cleaning out a dryer with top lint cleanout - YouTube
    Cleaning out a dryer: By a woman 2 of 2 - YouTube Make sure to clean the exhaust and that ductwork and outlet on side of house, too. Your dryer should last a long time after this if you keep it clean.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Whirlpool gas dryer does not heat up [ 2 Answers ]

I have a whirlpool gas dryer model LHI5701WO and today I turned it on and it does not heat up. The drum turns but no heat

Whirlpool gas dryer drum won't turn [ 1 Answers ]

Whirlpool gas dryer model LGR7646EQ. When the start button is pushed, the dryer hums for about 5 to 8 seconds and then shuts off. I can turn the drum by hand. A slight burning smell also. It appears to be an auto shut off. It will reset after a few minutes. I am looking for repair procedure,...

Whirlpool gas dryer no heat [ 1 Answers ]

Whirlpool gas dryer little or no heat

Want to turn Whirlpool gas dryer from LP bact to Gas [ 3 Answers ]

How do I convert my Whirlpool Gas dryer from LP back to Natural gas. I need to know what piece goes in the burner tube to regulate the Natural gas


View more questions Search