Ask Experts Questions for FREE Help !
Ask
    harshent's Avatar
    harshent Posts: 1, Reputation: 1
    New Member
     
    #1

    Feb 5, 2007, 02:21 PM
    Well Pump pressure switch chatters
    I live in a older home in a small rural town with a shallow well in the basement. I recently replaced the pump (it was leaking). The old pump was also cycling on and off sometimes very fast (chattering) both at cut off and cut on pressure. When I replaced the pump it seemed to fix it for a while but then it came back. I replaced the cheap pressure switch that came with the pump with a new 20-40 psi Square D switch. It worked for a while but then it started up once again at both cut-off and cut-on pressures. I used to have a very small (19 gal) pressure tank and I could get the chattering to stop by adjusting the air pressure in the pressure tank. Finally the water line to the pressure tank broke so I replaced the tank with a new 44gal bladder tank. I followed the instructions and reduced the air pressure in the tank to 2psi below my pump cut in, and drained all the air out of the system. This did not help the chattering problem. I was told that my foot valve at the bottom of my well could be clogged that may be causing my pump to do this. Also I read some of your post about pumps cycling could be caused by a faulty check valve. Any ideas?
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    Feb 5, 2007, 04:03 PM
    "I was told that my foot valve at the bottom of my well could be clogged that may be causing my pump to do this. Also I read some of your post about pumps cycling could be caused by a faulty check valve."

    The foot valve is a check valve located at the bottom of the well while a check valve's located on the suction line above ground. They both do the same fuction. Regards, Tom
    TheSavage's Avatar
    TheSavage Posts: 564, Reputation: 96
    Senior Member
     
    #3

    Feb 5, 2007, 04:31 PM
    But the answer is yes a bad check [or foot ] valve could cause this. The pump builds up pressure, cuts off , the water runs back down the well.
    Tilak's Avatar
    Tilak Posts: 1, Reputation: 1
    New Member
     
    #4

    Feb 28, 2007, 08:56 PM
    Please explain the cut-in and cut-off pressures of a water pump.
    TheSavage's Avatar
    TheSavage Posts: 564, Reputation: 96
    Senior Member
     
    #5

    Mar 1, 2007, 03:27 AM
    Cut in means the pump starts, cut out the pump stops.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Lost pressure to pump [ 1 Answers ]

We have an above ground water pump connected to an underground storage tank. We just had the tank filled, but there is no pressure in the pump. How do we re-prime to get it going again? Chuck

New pressure pump leaks [ 1 Answers ]

I installed a pressure pump on the house 3' from the main water feed. Old pressures were 35 lbs static and 27 lbs residual during flow. Now we have 60 lbs residual during flow BUT.... the pump runs for 15 seconds after the flow stops which builds up 80 lbs static. The pop off valve on the hot...

Tank Pressure vs Pump Cut Out Pressure for Well [ 1 Answers ]

I am trying to increase my water system pressure to the minimum required 40 PSI to feed my reverse osmosis drinking water filter. However, the 33 gallon pressure tank for my well pump system says it is pre-charged at 30 PSI and that the cut in pressure for my pump should be set equal to that 30...

Wiring Timer Clock, Off /On switch to Pool Pump [ 3 Answers ]

I recently replaced an underground electrical line for my pool pump. Now I'm not certain of the hookup from the main power (220)to the timer clock (also 220)into the manual off/on switch mounted in it's own box on the back of the timer box, to the pump motor. Can anyone help me here. It's a single...

Limit Switch - Pressure Switch [ 0 Answers ]

Hello Folks, This weekend I've been playing with a heating system at my new apartment and I'm trying to figure out what the different componets do. I kind of followed the circuit but still have some missing links... 1-There are some terminals on the furnace's circuit board labeled LIMIT. The...


View more questions Search