Ask Experts Questions for FREE Help !
Ask
    detroitdeb's Avatar
    detroitdeb Posts: 5, Reputation: 1
    New Member
    		  
    #1

    Sep 2, 2011, 08:02 AM
    TC-L42U12 where to get fuse and need what size it is or amps ?
    Have a panasonic TC-L42U12 no power or sound or picture .I think it is a fuse . Not sure where to buy or what number on the fuse .tv is in Ehrenberg AZ . Not a lot of stores out there .please help
    FadedMaster's Avatar
    FadedMaster Posts: 1,510, Reputation: 148
    Ultra Member
    		  
    #2

    Sep 3, 2011, 04:35 AM
    You can get fuses just about anywhere. The fuses on the power board are not specialized. However, chances are if the fuse has gone, it will go again. Usually something takes the fuse out. So it's possible you have a bad power board.

    Do you have a red standby light? Does it blink? If so, how many times does it blink? Does it only start blinking after you push the power button? Or does it blink right after plugging it in?
    detroitdeb's Avatar
    detroitdeb Posts: 5, Reputation: 1
    New Member
    		  
    #3

    Sep 6, 2011, 11:49 AM
    Nothing no blinking light nothing!!
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #4

    Sep 6, 2011, 02:27 PM
    Did you check the fuse for continuity, or power in and out?
    Sometimes the writing is Extremely small. Look very close with a magnifier.
    DigiKey should have it:
    http://www.digikey.com/?curr=USD
    Knowing the length and diameter will help.
    FadedMaster's Avatar
    FadedMaster Posts: 1,510, Reputation: 148
    Ultra Member
    		  
    #5

    Sep 6, 2011, 04:19 PM
    Yep, as Strat mentioned, it'll be printed on the fuse itself. Also check it for continuity with a meter. If you don't have continuity, then the fuse is bad.

    We can't tell you exactly what size the fuse is without at the very least knowing which fuse it is. There are about 3 standard fuses on the power board of that model (if I recall correctly).
    detroitdeb's Avatar
    detroitdeb Posts: 5, Reputation: 1
    New Member
    		  
    #6

    Sep 7, 2011, 07:47 AM
    Thanks I'll just order all three that way I have them with me .when I go to az... thanks
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Amps are too high on fuse [ 3 Answers ]

Coleman Furnace Model # G9t08012upb13c 3 Amp fuse keeps blowing. We tested board and the amperage cosistantly above 3 Amp rating. Why is this happening and how can we fix it?

I am hooking up a Hot tub with a max fuse size of 50 amps. [ 3 Answers ]

I am hooking up a hot tub rated for a 50 amps max fuse size. I already have the #8 thhn and 1/2 liquid tight flex conduit. Will the #8 wire be enough for 50 amps.

Replacing fuse panel and amps [ 0 Answers ]

I am getting my wiring updated along with my fuse panel. Right now it has a old bull dog set up with the push button fuses. There really hard to find replacement fuses, and two of them are blwon and will not reset! One of the fuses is for my stove, and the other runs the lights and fan in my...

AWG size for 40 amps. [ 3 Answers ]

Remodeling kitchen. I now have an oven with 8AWG and a 30 amp breaker. The new oven requires 40 amps. The run is 20 feet. Will the 8 awg do with a 40 amp breaker? Thanks, Shortround3.

View more questions Search