Ask Experts Questions for FREE Help !
Ask
    drband's Avatar
    drband Posts: 1, Reputation: 1
    New Member
     
    #1

    Feb 1, 2007, 04:12 PM
    Can I use a 50 AMP GFCI where I once had a 60AMP?
    I have a LA SPA Quest 8500 hot tub in my backyard (inherited from previous homeowner). It has a 60AMP GFCI box connected on the outside of the house which is then connected to a 60AMP breaker on the main in the basement. My 60 AMP GFCI oustide occasionally trips. I don't think there is anything wrong with my tub as I've had it attended to by local spa companies. But, I do think that my breaker has just gone bad with time. I am finding however that 60 AMP GFCI breakers are very difficult to find. I've noticed that many hot tub companies are selling 50 AMP GFCI with their tubs. Is it possible to put a replacement 50 AMP GFCI outside which would then be connected to the existing 60 AMP Breaker in the house and still run the hot tub? Any input is appreciated. Thanks!
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #2

    Feb 1, 2007, 04:35 PM
    You can physically make the switch, it will fit. However, you need to know the amp requirements of your spa. If the manuafacturer used a 60 amp I'm going to guess they couldn't get away with a 50 amp, or they would have. You might not find the 60 at your hardware store but I'd order a 60 on line before thrying to make a switch.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #3

    Jun 4, 2007, 05:47 PM
    If 50 Amp GFI is Ok for Yours, I would change inside with 50 Amp 2 pole Breaker.
    Even if you have it "attended", corrosion in motor can leak to ground, causing ground fault.
    If Motor can be unplugged or disconnected safely and easily. See if breaker trips. If it doesn't , bad motor, if it does, try blower, etc...

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Wiring Hot Tub and using a 50 Amp Double Pole GFCI Circiut Breaker [ 10 Answers ]

:confused: I keep getting the GFCI breaker tripping after wiring my hot tub. I wired 2 hot Red and Black to the proper terminals and the White to the neutral and the Bare Copper to the ground Post at the tub. I am using 6-3 w/G per instructions. Could the GFCI breaker be bad? When I wire...

20 amp double pole gfci [ 9 Answers ]

I am working on an addition and am installing a whirlpool tub. The tub requires 2 - 20 amp GFCI protect circuits: 1 for the pump and 1 for the heater. I ran 12/3 wire in the walls thinking I could have the BLACK wire go from 1 GFCI breaker to the pump outlet and the RED wire go from a 2nd GFCI...

GFCI & Switch [ 1 Answers ]

Can a GFCI be wired to run of a switch?

Gfci [ 5 Answers ]

How do you install GFCI Recepticles properly with old wiring in a house?

Gfci [ 1 Answers ]

Is there ever a situation where it makes sense to have a GFCI outlet on the same circuit as a GFCI breaker? Will having a GFCI outlet on the same circuit as a GFCI breaker cause any damage? I recently bought a house and found the situation noted above.


View more questions Search