Ask Experts Questions for FREE Help !
Ask
    jmorton78's Avatar
    jmorton78 Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Dec 23, 2010, 08:26 PM
    Need help wiring my furnace blower motor
    I have a dayton model 6k376 and I only have a black, white and green wire coming from the furnace. How do I hook them up to my motor
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #2

    Dec 23, 2010, 11:27 PM
    The motor has a wiring diagram on the side,, step by step,, it might help for you to tell us what color wires are coming out of the dayton motor
    jmorton78's Avatar
    jmorton78 Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Dec 24, 2010, 06:02 AM
    There aren't any wires coming out, they are connected inside the wiring plate you take off to connect the furnace wires. But there is a terminal with a white black and yellow wire connected to it with one open terminal (to plug another wire in). There is a terminal with an orange and black, a terminal with a red wire, one with a yellow wire and open terminal, and one terminal with two open spots. The diagram says nothing about the white and green wires. They are all connected by connectors. I would do trial and error but I'm worried that I would fry the motor.
    jmorton78's Avatar
    jmorton78 Posts: 3, Reputation: 1
    New Member
    		  
    #4

    Dec 24, 2010, 08:00 AM
    Comment on jmorton78's post
    Now I got it working but it turns off after a min or two. What would cause that?
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Wiring up a new blower motor for my furnace [ 6 Answers ]

I have a Rheem furnace that is at least 10 years old, could be as old as 20. I had to replace the blower motor which was a 1/4 hp and the motor I replaced it with was able to be 1/8, 1/4 or 1/2 hp. Depending on how it is wired. From reading on the capacitor I could hook this up as a 1/2 hp which...

Blower motor wiring for wood furnace [ 1 Answers ]

Would like to know how to wire my wood furnace(Hotblast 1557M) with twin 550 cfm blowers, to my gas furnace blower for some circulation assistance when the wood stove blowers cycle. Also, when gas furnace is needed; would just like it's blower to operate on it's own. Is this possible? Wood stove...

Goodman furnace will ?heat motor? And blower motor will run but not at same time [ 2 Answers ]

I have a 2 year old Goodman, gas, no heat pump. There is a flashing LED that blinks once ever 4 seconds. Also, blower motor does not stay on always. We did smell something like an electrical burn. I'm guess my blower motor is fried?

Very old furnace to new Blower motor wiring [ 10 Answers ]

Hello, I have an old GE furnace, from the 1960's I believe. Today the blower stopped working. I pulled the blower unit out and found the bearings destroyed on one side. I had no luck finding new bearings. So as a last resort a friend had an old furnace he had repalced with a blower motor that...

Furnace blower motor wiring [ 2 Answers ]

I have an old furnace blower that I want to convert to a shop air clearner. I want the motor to operate from a normal 110 volt switch. My question is which wires do I connect to the switch? The motor is a 1/2 hp Emerson Model K55HXLGG3702 It has 6 wires - black, white, brown, blue, red, yellow

View more questions Search