Ask Experts Questions for FREE Help !
Ask
    AlexDuke's Avatar
    AlexDuke Posts: 3, Reputation: 1
    New Member
     
    #1

    Aug 31, 2010, 03:56 PM
    Poulan Pro Blower won't turn over, only back fires with starter fluid...
    I have a Poulan Pro Blower Model #: PBV200.

    It wouldn't turn over, so tested for spark, seems to have a powerful spark, then tested fuel filter and air filter, seemed clean. Being all it takes for these to run is air, fuel and fire. I tested the gas and gas lines, even replaced with fresh fuel, since it did sit through the season.

    Fuel lines looked good and clean, questionable carb, looked like the diaphragm has rotted away, so replaced the carb, cleaned out muffler since it at first felt like I was getting a little resistance. There was a mud dabbers nest, but it's clean now.

    Tested, still won't turn over, poured a little fuel on air filter, still nothing. Used starter fluid again with the muffler off, got it to back fire a few times, and sounded like it almost turned over, but then shut off.

    Upon inspecting the flywheel it all looks like it isn't bent or anything. What else could it be that is causing it not to turn over? I am dumbfounded right now!
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #2

    Aug 31, 2010, 05:19 PM

    Initial carb setting?
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
     
    #3

    Aug 31, 2010, 08:16 PM

    Check you compression , you will find real hi or real low.
    That unit has a one ring piston, the ring is probably stuck,if you take the muffler off and look in and push on the ring ,there will be no movement there are two ways to fiw it one take apart and put a ring in it,the other is throw away and buy a new blower.
    AlexDuke's Avatar
    AlexDuke Posts: 3, Reputation: 1
    New Member
     
    #4

    Sep 1, 2010, 08:24 AM

    I haven't adjusted either adjustment as far as carb settings go, do to them being so touchy. Left factory settings. I will check the ring and see. Could it possibly be a bent shaft? It seems to move fluidly and have compression?
    AlexDuke's Avatar
    AlexDuke Posts: 3, Reputation: 1
    New Member
     
    #5

    Sep 1, 2010, 08:57 AM

    Did just notice cylinder had some how come loose from the shaft housing on one side, which potentially could be where the loss in compression is, after taking the piston and ring out, the ring was cracked. Obviously one end is supposed to be that way, however it was cracked in half.
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
     
    #6

    Sep 1, 2010, 08:56 PM

    Make sure there's no grooves in the cylinder walls.
    When you put the new ring on make sure the notch goes in the open end of ring.
    Sounds like your on your way.
    LUCK

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Poulan Pro Lawn Mower [ 2 Answers ]

My push lawn mower will start, but quickly sputters out. I removed the air filter to see if this was the culprit, but the results were the same. What next?

Poulan Pro belt change [ 5 Answers ]

My Poulan Pro 42" 17hp automatic riding mower has thrown the belt that is located directly beneath the floorpan. What is the best way to get to it and replace it?

Poulan Pro blower sm400 starter rope sticks [ 0 Answers ]

The starter rope on my Poulan Pro SM400 sticks when I pull it out. What can be done? Thanks for any help!!

Poulan Pro gas leaf blower/vac [ 1 Answers ]

I am having trouble keeping the thing running. I noticed that there seems to be a filter on the gas line in the tank. Could it be dirty and if it is then how or what do I clean it with. Would it be better to just replace the filter?

How to replace starter rope on poulan pro sm400 [ 1 Answers ]

Hi, I need to replace the starter rope on a Poulan Pro SM400 leaft blower. I have it apart but since the old rope broke off, I don't know how to attach the new one to the wheel. Thank You Carl


View more questions Search