Ask Experts Questions for FREE Help !
Ask
    larryf's Avatar
    larryf Posts: 3, Reputation: 1
    New Member
     
    #1

    Dec 21, 2006, 05:30 PM
    Older wall heater with no electricity to it?
    I have an older wall heater with no apparent AC connection. What is the rating of this heater in terms of voltage? I see a gas connection of course, but no AC. I am having a heck of a time connecting up a thermostat. The programmable thermostat didn't work. So I got a round CT87N round Honeywell thermostat. It says it's for 24 Vac heating. Can I use this thermostat?.

    There are only two wires coming off the wall heater. Where do I connect the two wires to the thermostat? Currently R &Rc are jumpered together.

    Thanks very much!!
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
     
    #2

    Dec 21, 2006, 05:59 PM
    Follow the wires and the gas pipe into the heater. They should meet at sort of a box. The box is a gas valve, and should have a label on it giving the voltage or millivoltage. Post what you find.
    larryf's Avatar
    larryf Posts: 3, Reputation: 1
    New Member
     
    #3

    Dec 21, 2006, 06:12 PM
    This is normail - no AC to the wall heater?

    All I could read was General Electric b60 Gas valve and a serial number...

    Thanks for your help!
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
     
    #4

    Dec 21, 2006, 08:28 PM
    Connecting the 2 wires to the R and W terminals of the thermostat may work if it is just a simple mechanical switch. If not, one of the people with wider experience here should be able to help.
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
     
    #5

    Dec 21, 2006, 09:23 PM
    Some older wall heaters use what is called a "pilot generator" to create it own voltage, about 750 millivolts which it 3/4 of one volt. This furnace uses a special thermostat that will work with millivolts. Check the new thermostat and see if it says it will work with millivolts. If not you will have to change it, and I an not sure you will find a programmable one.

    Do you have a thermocouple on your furnace?? If you do then it is not a millivolt system, a millivolt system will have two wires coming off the pilot and going to the gas valve, then there will be two wires going to the thermostat. If you pilot is lit and the generator is working, you can touch the two wires together at the thermostat and the furnace should come on it about 30 seconds.
    Post more information if you find more.
    larryf's Avatar
    larryf Posts: 3, Reputation: 1
    New Member
     
    #6

    Dec 22, 2006, 12:03 PM
    Hi... the heater goes on even when there's no thermostat attached!. I have to shut off the gas to the gas valve to shut the heater off!. It is a millivolt ssystem..

    What is the solution?

    Thanks very much!

    Larry

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Wall Heater Problem [ 7 Answers ]

My home is heated by an older model Empire wall heater. The heater did not start up last week and I could not figure out the problem so I called a repair man. He found a wire in the heater that had become disconnected and hooked it back up, after which he was able to start the heater by lighting...

GFCI for wall heater? [ 2 Answers ]

I'm installing a wall heater in a small bathroom. The heater will be next to a pedestal sink and controlled by a wall switch. The heater will be on its own 12 gauge, 20 amp circuit. The question is, should I install a GFCI outlet in the line before the heater to give ground fault protection to...

240 Volt Wall Heater [ 7 Answers ]

I have hooked both wires to separate circuit breakers one white and one black and connected them to the black and red leads from the wall unit and the ground poles on the heater box but it does not work. If I disconnect the white wire from the circuit breaker and connect it to the white posts on...

240 volt wall heater [ 3 Answers ]

I am installing a wall heater in a room. The heater has a ground wire and a black and red wire. How do you hook it up to 240 volts? Do I need to run four wires, three wires? I have a double breaker at 20 amps already in the circuit breaker panel but what do I need to hook up power. Does one of...


View more questions Search