Ask Experts Questions for FREE Help !
Ask
    bolayton's Avatar
    bolayton Posts: 2, Reputation: 1
    New Member
     
    #1

    Jun 21, 2010, 04:04 AM
    Wellsaver pressure tank troubleshooting
    I just installed a 20 gal percarged tank and a new pump. The pressure is fine and the pump shuts off at 40psi , but when I turn on my faucet or any orfice there is a lot of air. Can sombody HELP with this?
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    Jun 21, 2010, 05:00 AM
    When first installed the bladder is pressured by air and not water.
    Read your instruction manual. Didn't it mention that to start with a new bladder tank there will air in the bladder until it works out and is replaced by water. Give it time to break in. Good luck, Tom
    Attached Images
     
    bolayton's Avatar
    bolayton Posts: 2, Reputation: 1
    New Member
     
    #3

    Jun 21, 2010, 05:41 AM
    Wellsaver 20-gallon pump tank troubleshooting
    Thanks Speedball1, This problem has been going on for 3 days now. How long should this process take ? The tank bladder was precharged to 25psi and with my 20-40psi p/sw I took the percharged pressure to 18 psi.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #4

    Jun 21, 2010, 06:11 AM

    Shut bthe power off to the pump and open a cold water faucet to bleed off the pressure. Now set the bladder tank pressure to 2 PSI under the cut in point. In your case it should be 18 PSI.
    When you first install a bladder tank the bladder will compress with air. This will gradually work out with use, how long will depend on time and how much you use it. Be patient the air will disappear in time. Cheers, Tom

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

52gallon WellSaver pressure tank [ 7 Answers ]

I have a brand new wellsaver pressure tank. I have set the pressure switch for 30/50. This part of it seems to be working well, but every time I have checked the pressure in the tank I get different readings. Anywhere from 24psi to 40psi and then back to 24 then to 32 and so on. I want to get...

Wellsaver pressure tanks, troubleshooting [ 2 Answers ]

I have a wellsaver 12 gallon tank mounted next to pump for a shallow well irrigation system. When the pump is running I can get water out but the pressure will not build up in tank enough to cut off pump which is set about 40psi. There is only air that is released from Shredder valve when depressed...

Well Pressure Tank replaced w/WellSaver 36 - Lot's of air [ 6 Answers ]

Replaces a well pressure tank with a New WellSaver 36 pressure tank and now have a lot of air in system. What is the issue of air in the system, even after repeated air bleads?

New Wellsaver Pressure tank is banging pipes [ 1 Answers ]

I just replaced my submersable well pump and my pressure tank with a Wellsaver bladder pressure tank. Now, after the water isn't running for a while, the pipes begin to bang and when I look at the pressure tank while this is happenning, the reading on the gauge is bouncing. Help?

Installing a Wellsaver pressure tank [ 1 Answers ]

I just purchased an 86 gallon Wellsaver tank and I'm not finding installation instructions. The only "instructions" I've found is a diagram on the side of the box. Are there more specific instructions available.


View more questions Search