Ask Experts Questions for FREE Help !
Ask
    DaBears's Avatar
    DaBears Posts: 7, Reputation: 2
    New Member
    		  
    #1

    Dec 5, 2006, 12:51 PM
    Goodman 4 ton HP
    I have a Goodman 4 ton HP CPJ60-1. Outside unit was coming on but the inside blower motor did not come on. Now the outside unit does not come on at all in either mode.
    Where should I look?
    NorthernHeat's Avatar
    NorthernHeat Posts: 1,455, Reputation: 132
    Ultra Member
    		  
    #2

    Dec 5, 2006, 01:57 PM
    Check breakers, check for 24 volts to the control board at Y and common
    DaBears's Avatar
    DaBears Posts: 7, Reputation: 2
    New Member
    		  
    #3

    Dec 5, 2006, 02:28 PM
    Quote Originally Posted by DaBears
    I have a Goodman 4 ton HP CPJ60-1. Outside unit was coming on but the inside blower motor did not come on. Now the outside unit does not come on at all in either mode.
    Where should I look?
    Breakers are fine, I'll have to check for volts at the control board. Inside blower motor hums but doesn't start, cage spins freely.
    DaBears's Avatar
    DaBears Posts: 7, Reputation: 2
    New Member
    		  
    #4

    Dec 5, 2006, 02:29 PM
    If the inside blower was not running is their something that would trip the outside unit because of this?
    NorthernHeat's Avatar
    NorthernHeat Posts: 1,455, Reputation: 132
    Ultra Member
    		  
    #5

    Dec 5, 2006, 02:47 PM
    No there isn't. I'm curious why the indoor blower isn't running though, maybe a bad capacitor. Does the motor get really hot?
    DaBears's Avatar
    DaBears Posts: 7, Reputation: 2
    New Member
    		  
    #6

    Dec 5, 2006, 02:50 PM
    Yes, motor gets very warm and stops humming, I will replace the capacitor. Still puzzled on why the outside stopped running
    NorthernHeat's Avatar
    NorthernHeat Posts: 1,455, Reputation: 132
    Ultra Member
    		  
    #7

    Dec 5, 2006, 02:54 PM
    Yes it sounds like the motor or capacitor are bad, thermal protector finally opens and turns it off when it gets to hot.
    seve tec's Avatar
    seve tec Posts: 1, Reputation: 1
    New Member
    		  
    #8

    Feb 21, 2010, 11:22 AM
    The out side stops because of the high limit pressure cut off switch, located on the high pressure side, if the indoor blower motor stops your high pressure will rise to the point the high limit switch switch cuts off the out sided unit. Be thankful for this or your compress will over heat and cost you big bucks!!
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Goodman Furnace [ 2 Answers ]

How old is my Goodman furnace and how efficient is it? Model GUEQ80-4REVS Serial #910482720

Goodman Furnace [ 2 Answers ]

What does A three blink code on a Goodman 80 plus gas furnace mean

Goodman furnace [ 2 Answers ]

My Goodman furnace will light and then go out. This will occur 3 times, then will quit running. The control board blinks 1 time and tells me to Check Gas flow, gas pressure, gas valve, and flame sensor. It seems to have gas going to the valve. Could this be a bad gas valve? Or a bad Flame...

Goodman furnace [ 17 Answers ]

I have a goodman furnace. Forced air. No a/c. I turn the power on and she starts. Thermostat is off. No wires are crossed that are visible. The pilot does not ignite but the heating element is on. No gas seems to be coming through. Any suggestions? The furnace is only a year and a half old.

1979 Chevy 1-ton speedometer problems? [ 3 Answers ]

The speedometer in my truck works every now and then. Sometimes it does, and then sometimes it doesn't. Any solutions?

View more questions Search