Ask Experts Questions for FREE Help !
Ask
    rickmcbrid's Avatar
    rickmcbrid Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Feb 10, 2010, 05:53 PM
    P trap gaskets
    “P” trap leaks on the tapered ends that do NOT use a gasket, but compression to seal connection. How do I stop the leak?
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
    		  
    #2

    Feb 10, 2010, 06:01 PM

    You could use some teflon or pipe dope on the compression joint and see if it works, or simply replace the p-trap. If you are thinking about replacing the trap, before you do, just tighten the nut as much as you can by hand, then snug it a little more with a pair of pump pliers(channel locks). Please do let us know how things work out. Lee.
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
    		  
    #3

    Feb 10, 2010, 08:14 PM

    When I have the problem that you are describing I coat the face of the beveled joint with some rectorseal.
    rickmcbrid's Avatar
    rickmcbrid Posts: 3, Reputation: 1
    New Member
    		  
    #4

    Feb 11, 2010, 12:09 PM
    Thank-you for your interest and help. I applied silicone to the matching bevels, under the compression ring (nut) and to the threads. So far so good! NO LEAKS!!
    suthern kumfert's Avatar
    suthern kumfert Posts: 12, Reputation: 1
    New Member
    		  
    #5

    Feb 11, 2010, 04:13 PM
    Quote Originally Posted by rickmcbrid View Post
    Thank-you for your interest and help. I applied silicone to the matching bevels, under the compression ring (nut) and to the threads. So far so good!! NO LEAKS!!!
    They also sell an epoxy that I have use as a last resort.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
    		  
    #6

    Feb 11, 2010, 05:44 PM

    Those fittings that use compression do have gaskets of sorts.

    Look at the "washers" at the bottom of this page: Tubular bathroom drain products and p-traps and sink drains from FAMOUS PLUMBING SUPPLY

    To help seal, use a small amount of plumber's (Silicone) grease.

    Inspect fittings for burrs.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Thermostat gaskets [ 1 Answers ]

I have a 94 Silverado. I'm going to change the thermostat. In the past I have used the paper gaskets that fit around the water outlet housing. There is also a rubber seal that pops up when doing a search for thermostat gaskets. Should I use the rubber seal and place it in the thermostat housing...

Head gaskets going out [ 2 Answers ]

I have a 1991 buick regal and while I'm driving the car just cuts off where ever I am and I have to let the car sit awhile before I can start it again and under the hood I smell burning oil but I have to keep putting water in the radiator I took it to the shop and they said my head gaskets are...

Gaskets and pipes [ 2 Answers ]

I have a big questions if you buy a condo which was gutted and everything is brand new yoou been living there 2 years in September and one night you are in the kitchen and turn on the water in the sink and water starts spraying all over the place and coming out of the bottom of the faucet,and then...

How do I replace skimmer gaskets? [ 2 Answers ]

Hello all, Our vinyl pool liner was replaced about 9 months ago ( in-ground 15' X 36' ) and recently, we noticed that the water level drops by about 3 to 4 inches every week. I suspect that the leak is around the skimmers since the water level or leak seems to stop by about an inch above the...

View more questions Search