Ask Experts Questions for FREE Help !
Ask
    shadyslim's Avatar
    shadyslim Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Jan 30, 2010, 04:25 PM
    Rheem Pro Series Dual Fuel.
    Condensate line froze. Replaced and checked drain pan. OK. Fan will blow but unit will not fire burners. Is thbere a reset switch?
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
    		  
    #2

    Jan 30, 2010, 05:05 PM

    Did you turn the main power off and then back on to the furnace to reset the fault on the control board?
    shadyslim's Avatar
    shadyslim Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Jan 30, 2010, 05:39 PM

    Turned breaker off waited Ten seconds. Turned back on still doing same.
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
    		  
    #4

    Jan 30, 2010, 05:45 PM

    Still doing the same? Need more info.
    shadyslim's Avatar
    shadyslim Posts: 3, Reputation: 1
    New Member
    		  
    #5

    Jan 30, 2010, 05:47 PM

    Fan Blkowing out cold air. Burners not lighting.
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
    		  
    #6

    Jan 30, 2010, 05:57 PM

    Count the blinks on the control board. To decode the blinking light should be a list on the blower door telling what's wrong. Let us know.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

NO HEAT Rheem Classic 90 series 3 years old [ 6 Answers ]

I have a Classic 90 Series Rheem RGRA series upflow/downflow furnace 3 years old. Intermittently, the furnace will not flame up or give out heat. Sometimes it only blows cold air. Sometimes, it locks out (middle green light flashing once then pausing). The furnace repair company came out and...

Rheem classic 90 series pilot light [ 2 Answers ]

The pilot light on my furnace went out & I can't figure out how to relight it. It did it a few months ago & my ex (who wasn't my ex at the time) found the instructions & easily got it going again. Since the weather was good I had the thermostat off for about a month just like I always do. Now it is...

Dual fuel rheem furnace not working, defrost control board replaced still not working [ 1 Answers ]

Hello there, I have a Rheem furnace and is only one year old. Recently my furnace didn't come on so I had someone come out and look at it and it turns out it was the defrost board on the heat pump that was bad. I replaced the board with a new one and turned the system on and it worked on heat and...

Will XP PRO work on a 64 bit Dual Channel PC [ 2 Answers ]

I am building a new PC using a gigabyte 939 Dual Channel MB with 2 gigs of Dual Channel DDR ram. I have most of what I need bought, but I bave heard that a lot of devices I use don't have 64 bit drivers yet so can I continual using XP PRO on this PC until enough drivers are available. Also would...

Dual Booting W2k3 Server and XP pro [ 4 Answers ]

Hi All, I've a working custom built Desktop PC with Win XP Pro running without any issues. My 80GB HDD is partitioned into 4 partitions of 20GB each. Now I'm curious to know whether I can install Windows 2000 Server, so as to make it a dual booting system. Someone told me that I can't do so...

View more questions Search