Ask Experts Questions for FREE Help !
Ask
    blackdoggracie's Avatar
    blackdoggracie Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Jan 5, 2010, 02:14 PM
    How to wire a furnace transformer
    I acquired (was given) an old Lennox furnace ID# G9D-55-M-1. The transformer was missing, I bought a new one a 115/24V model. I question the wiring configuration for the fan/gas valve and limit switches...
    I am very capable of wiring the furnace controls just don’t have the knowledge to ensure that the wiring is correct. How do I wire this furnace to make it operate as it should via a thermostat?
    Thanks
    Ken
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #2

    Jan 5, 2010, 02:19 PM
    An old Lennox, even when it was new,, it wasn`t much to brag about. But,my thoughts aside.. there should be on the inside of access door a wiring diagram that could led you where you need to go,, if not Google lennex, and have the model number with you,, good luck
    blackdoggracie's Avatar
    blackdoggracie Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Jan 5, 2010, 02:24 PM

    Unfortunately that door is missing... and the diagram.
    I didn't mention it is for my garage have googled Lennox just have not seen a diagram yet. I was hoping someone could tell me "generically" how to do this. I would think its straight forward.
    Thanks
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #4

    Jan 5, 2010, 02:42 PM
    The only GD9 unit listed is for a York/Coleman brand. There are many different items included on some furnaces and not on others so the factory wiring diagram is a must. Also if you are going to put that into your garage you have to elevate the furnace off the floor a minimum of 18 inches and install protection posts so your car cannot hit the unit. FYI. This is required by code as well as the manufactures instructions. Also the blower access door muct be replaced and the return air take from outside the room. This is also in the code since it is a fossil fuel furnace(gas burner) I believe.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

How to wire a pool light transformer [ 6 Answers ]

I was supplied with an Intermatic 120-12v transformer. There are no wiring connection diagrams. The transformer has 4 wires( bk, wh, bl and y)on one side and 2 black wires on the other side. How do you connect supply and the pool light to this?

HT Wire Delco furnace transformer? [ 1 Answers ]

IM WORKING ON A DELCO- HEAT CONDITIONAIR FURNACE. Model# DGH100B2, Serial- 414 I need to replace the transformer. How exactly do I wire up the new Transformer?

How do you wire a transformer [ 1 Answers ]

How do you wire a transformer

Transformer / how to wire afuse on the low voltage side [ 2 Answers ]

I have a Nordyne model E!EB-015HA furance, transformer burns out after 1 minute .It was suggested by one of your good people (can't find I.D. ) to add an inline fuse to the transformer so thefuse blows and not the transformer. Where do I wire the inline fuse. On the 24 v side or the 240 side, ...

Looking for control wire on transformer [ 5 Answers ]

I am installing a new HONEYWELL T8601D2019 - it won't power on. I realize it needs a control wire connected to the C... I can not figure out which wire off my transformer is the control. I have three blue wires, a red, black, and white. Red, black and white are all connected to the unit in...

View more questions Search