Ask Experts Questions for FREE Help !
Ask
    pennstatemike's Avatar
    pennstatemike Posts: 4, Reputation: 1
    New Member
     
    #1

    Dec 29, 2009, 05:22 PM
    Water heater relief valve dripping
    I have a 12 year old gas water heater that was originally installed with a tank expansion unit. Last fall, the relief valve started to leak occasionally so I had the relief valve replaced. The leak still occurred and I would dump a bucket once every couple of weeks knowing that I would soon have to replace the expansion tank. Time goes by and 11 months later I've finally decided I need to replace the tank expansion unit because I know have to dump the bucket every day due to the cold weather.

    I measured my inlet water pressure on the outside of the house with the outside faucet and it measured 65 PSI. I pumped the tank expansion until up to 65 PSI when I installed it, but unfortunately, I'm still letting a drip from my water heater. The tank expansion unit was definitely part of the problem, because it was filled with water when I removed it.

    I'm not sure what else to do? Do I need to replace the relief valve again because of all the drip that has occurred over the past year?
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    Dec 29, 2009, 05:43 PM
    I pumped the tank expansion until up to 65 PSI when I installed it, but unfortunately, I'm still letting a drip from my water heater.
    Whadda you mean you pumped up the expansion tank? And to house pressure already.
    A expansion tank does just that. It expands! I
    You're treating it like a bladder tank on a pump system. Where's the tank going to expand to if you pressure it up to house pressure. That's right Sports Fans! It expands out the T & P Valve because that's the only place left. Try letting all the pressure out of the tank and see if the leak doesn't go bye-bye.
    If you get water out of the snifter valve when you bleed off the pressure then replace the tank. The membrane's ruptured. Goodluck, Tom
    pennstatemike's Avatar
    pennstatemike Posts: 4, Reputation: 1
    New Member
     
    #3

    Dec 29, 2009, 09:45 PM
    The directions said that I had to match the expansion tank PSI to the inlet water pressure when I installed it. When I originally put it in, the PSI on the expansion tank was 28, and it was still leaking at that point, so I pumped it up to 65. I re-read the install directions, and that is where I saw that they had to be equal.

    Which one is the sniffer valve? The only leak (slow drip) is from the relief valve.


    By the way, it's a WellSaver LET2. It says, "The expansion tank air charge must be adjusted to match the incoming water pressure".
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #4

    Dec 30, 2009, 07:05 AM

    My bad! I missed this part.
    The tank expansion unit was definitely part of the problem, because It was filled with water when I removed it.
    The snifter valve is the valve on top of the tank and if you get water out of it then you must replace the expansion tank. I was in error and yourWellsaver Let2 tank must be set to house pressure. However if water comes out of the snifter valve the bladder'S ruptured and the tank must be replaced. I apologize for jumpling on you for pressuring up your tank In my area we use the tanks that are precharged. Check the snifter valve and let me know if you get air or water out of it. Good luck, Tom
    Milo Dolezal's Avatar
    Milo Dolezal Posts: 7,192, Reputation: 523
    Plumbing Expert
     
    #5

    Dec 30, 2009, 11:02 AM

    Pressure Relieve valve will leak if there is High Pressure or Water is too Hot. Is your thermostat working properly ? Do you feel like you get steaming hot water from your faucets ?
    pennstatemike's Avatar
    pennstatemike Posts: 4, Reputation: 1
    New Member
     
    #6

    Dec 30, 2009, 05:40 PM
    I ended up replacing the relief valve today. After a year of constant leaking, it must have worn itself out. It's been 8 hours and no leak so I hope this situation is finally under control.

    Thanks to all for the advice.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Dripping T&P relief valve on AO Smith water heater [ 2 Answers ]

I own a 2 year old 2 family house. I have 2 AO Smith 50 gallon (high efficiency water heaters). They are 2 years old. Last week I noticed that the T&P valve on one of the units developed a very slow drip. Literally 1 drop every few minutes (very minimal). I opened and closed the valve for a...

Can I plug outlet of dripping water pressure relief valve [ 1 Answers ]

The Wilkins water pressure relief valve at the inlet to the house supply is dripping. Can I safely plug the outlet where the drips are flowing, until I replace the entire valve? Is the valve strong enough to hold pressure once it is plugged?

Waterheater very little hot water & dripping relief valve [ 2 Answers ]

Hi, I have installed a new electric waterheater 100 Litres supply pressure 6 bars, pressure regulating valve set at 4 bars pressure relief valve 5 bars, when electricity switched on thermal expansion increases pressure to 8 bars, pressure relief valve starts leaking correctly at approx 5 bars but...

Water Heater Pressure Relief Valve [ 1 Answers ]

Private Message: Water heater pressure relief valve Today, 06:15 PM Kenvirani New Member Join Date: May 2008 Posts: 0 Water heater pressure relief valve --------------------------------------------------------------------------------


View more questions Search