 |
|
|
 |
New Member
|
|
Dec 12, 2009, 10:51 AM
|
|
Heat zone valve
I have a 2 story house one thermostat downstairs(does not have different zone settings), with one lennox merit series gas heat system. The unit has a synchron zone valve in the ductwork, air passes through first zone(downstairs) to get to second zone(upstairs). The zone valve opens when unit is turned off but stays closed when unit is turned on keeping heat from getting to upstairs. I took synchron motor out so it would stay open and keep both floors heated. What are some drawbacks of doing this? Or what can I do to fix system to work the way it is supposed to be designed? Any help would be greatly appreciated.
|
|
 |
Heating & Air Conditioning Expert
|
|
Dec 12, 2009, 03:14 PM
|
|
The zone control for the upstairs is only supposed to open when the upstairs calls for heat. Sounds like it is wired in reverse possibly due to a thermostat change with improper wiring,
|
|
 |
Plumbing Expert
|
|
Dec 12, 2009, 03:36 PM
|
|
If you only have one thermostat, there is really no need for a damper upstairs. I say you'll be just fine with keeping the upstairs damper open as you've done.
|
|
 |
New Member
|
|
Dec 13, 2009, 04:26 PM
|
|
I tried leaving the damper open last night and it way to hot upstairs and not hot enough downstairs. I do think they wired the thermostat wrong. It looks like it is a thermostat that is only designed for one zone. I bought a thermostat that is designed for a 2 stage baffle system. But I notice it has a w2 slot for the baffle for heat and a y2 for the baffle when on a/c but I only have one wire running to the baffle. I have it connected to w2 for now since we are running heat but not sure if I will need to run anything to y2 for a/c in summer? Also not all to sure this is going to work right, I will have to see tonight if it kicks in. How does it know when to kick heat off for upstairs without a thermostat?
|
|
 |
Heating & Air Conditioning Expert
|
|
Dec 13, 2009, 07:03 PM
|
|
To have a true 2 zone setup using the design you have you need to have 2 separate thermostats with each one installed in the area for which it serves.
It seems to me you have a few pieces of your control system missing as far as I can tell. Your best bet at this time is to call local for a on site HVAC repair person since we cannot really see what you have from here.
As you mentioned leaving a damper opened especially one going upstairs where the heat accumulates naturally does not work and doing that can turn the area into an oven in short order. Adjustments to the furnace controls might also be necessary and that is another reason to get on site help with this situation.
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
NO Heat in One Zone of Multiple Zone System
[ 6 Answers ]
The heat in our four zone house is working except for one zone. Digital Honeywell THermostat lights up when programmed, little flame picture appears and click noise is heard, just like other thermostats, but no heat in that zone. Any ideas what is wrong or how to fix. Thanks
Dual zone - no heat in zone one
[ 1 Answers ]
I have a carrier forced air dual zone heating and cooling system with programmable t-stats at the first and second floor of my house. The unit is in the attic. The problem is at the first floor. The heat does not work at this level. When the user set temperature goes below 3 degrees than the room...
2 zone oil heat, 2nd zone runs 1st zone
[ 1 Answers ]
Hi,
We have a 2 zone oil burner. The 1st zone (upstairs) runs separately and works no problem. The 2nd zone(basment), when we try to run 2nd zone separately , it seems to run zone 1(upstairs) and the baseboard heating upstairs gets hot and heats zone 1 even thought we have the t-stat set low...
Zone valve
[ 1 Answers ]
Got a white rogers zone valve spinning and not stopping ,has my end switch burned out .
View more questions
Search
|