Ask Experts Questions for FREE Help !
Ask
    tommywilliford's Avatar
    tommywilliford Posts: 2, Reputation: 1
    New Member
     
    #1

    Dec 9, 2009, 09:10 PM
    Ground wire and hot show charge
    Replaced all the power outlets in my bedroom. Two of the power outlets did not work, so I thought I blew a fuse. I did not. I tested the wires for power and I got a charge on my voltage meter by touching the one of the hot wires to the ground, but when I touch the hot to the neutral no charge. Both outlets have two hot and two neutral. The person that did the work before obviously didn't know what they were doing from other work I have found. Could it be that they switched the neutral and the hot when they wired it in the past or might there be another problem?
    Missouri Bound's Avatar
    Missouri Bound Posts: 1,532, Reputation: 94
    Ultra Member
     
    #2

    Dec 9, 2009, 09:25 PM
    Well... if the neutral was hot, it would show when you meter from the neutral to ground. Did the outlets work before you replaced them? I suspect you have an open neutral somewhere. You said both outlets have two hot and two neutral... are either of these outlets switched? Did you wire the outlets the same way as the old ones?
    tommywilliford's Avatar
    tommywilliford Posts: 2, Reputation: 1
    New Member
     
    #3

    Dec 9, 2009, 09:37 PM
    The neutral doesn't show charge no matter what I do. The hot and the ground show power. The plan is to cover both of them and not use them. I do not know if they worked before (should have checked). I never intended to use them because I am installing a closet system that will cover them. I guess I know power is coming into the box because of the hot wire... would it hurt anything to try and swtich the neutral and the hot on the two wires coming it to see if it completes the circuit?
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #4

    Dec 10, 2009, 10:02 AM

    This sounds l9ke you dropped a neutral. The balck to ground/green shows poer so the black is hot. If black to white shows nothing then the white has a broken connection somewhere down the line. Check all of you receptacles starting with the nearest that works, follow the white toward the bad receotacle and look for poor connections. If back stabbed try releasing them and use the side screws

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Connecting neutral wire to ground wire in breaker panel [ 3 Answers ]

Can the neutral wire be connected to the ground wire at the neutral bar in the breaker panel?

Can I use a ground wire for a ground and live black or hot wire at the same time? [ 8 Answers ]

I only have 3 wires from my ceiling to connect to my fan/light, the black, white and bare ground. No problems setting up in this room to only one switch but I would like to have the duel fan/light switch in like in my other rooms without having to pull a wire from the ceiling down to the switch,...

Receptacles hot to neutral show no volts, hot to ground show 120v [ 1 Answers ]

Replaced four receptacles in parallel, checked for loose wires. Checked the gfi breaker and 120v leaving the breaker. Tested all receptacles with voltmeter showing 120v between hot and ground, shows no voltage between hot and neutral. None of the receptacles work. Got any ideas?

How do I wire a switch with pilot light with 1 black, 1 white, and 1 ground wire? [ 1 Answers ]

I replaced an outdoor outlet controlled by an interior switch with a Cooper gfci outlet and it tested fine. Then I replaced the existing switch with a Cooper switch with pilot light. The switch has one line coming into it with one white(hot), one black(neutral), and one ground. When I connect...

Can I use a single strand of lamp wire as the ground wire for a chandelier? [ 2 Answers ]

I am in the process of rewiring a chandelier to lengthen the chain. I have wired it using a single strand of the insulated lamp wire as the ground - is this safe/ok to do instead of using the exposed copper wiring I typically see for the ground?


View more questions Search