Ask Experts Questions for FREE Help !
Ask
    augirl716's Avatar
    augirl716 Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Nov 24, 2009, 05:53 PM
    No led light on a Janitrol GMP075-3
    I had the circuit board replaced but now have no led light at all... any suggestions on how to get the led light to come on... single mom with 2 kids and would like to save as much money as I can... think I should just call a repairman
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Nov 24, 2009, 07:38 PM
    Chexk to be sure the power to the furnace is turned on and that the blower door is on tight.
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
    		  
    #3

    Nov 24, 2009, 07:40 PM

    You say you had a board replaced, does that mean hat you paid someone to replace it. If so I would call them back and see what kind of warranty they offer with their work.

    Now a couple of questions; Are you sure that the breaker is on and are you sure that the door switch is closed.

    New boards are easy to ruin by static electricity so if I were you I would not try to install a second board myself without being grounded to the furnace.
    augirl716's Avatar
    augirl716 Posts: 2, Reputation: 1
    New Member
    		  
    #4

    Nov 24, 2009, 08:02 PM

    I had a friend replace it. He checked and all limits are good and all contacts are good... the board has power..

    The breaker is on and the blower door is tight... the fan is not on as it was before the new board was put in... no led light at all..

    Tried turning everything off and then turning heat back on.. nothing has gotten the led light to come on...
    I am clueless, but know that is cold here!
    KC13's Avatar
    KC13 Posts: 2,556, Reputation: 99
    Ultra Member
    		  
    #5

    Nov 24, 2009, 08:26 PM
    The board may be wired wrong. All the connections are individual, rather than the multi-connectors some use.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Trane XL90 won't heat -- 5 led flashes [ 2 Answers ]

I hava a Trane XL90 furnace that was installed new about 3 years ago (oct 2006). Yesterday it stopped heating; and only blows unheated air out the registers. The Control board Red LED flashes a code 5. The Green LED is flashing slowly. The local HVAC company looked at it and concluded that...

Janitrol GMP075-3 Rev B will not light [ 6 Answers ]

I tried firing up my furnace today for the first time this year, and it will not ignite. When the furnace is turned on the blower motor starts, the igniter lights up, I can hear a relay click (assuming the gas valve relay) the funace does not ignite a flame, I do not smell gas, the gas valve is on,...

Goodman GMP075 [ 1 Answers ]

the furnace is tripping on high limit , not rollout. It will initiate a call for heat. The flue fan will run the air switch will make and the ignitor will glow. The MV comes on and the furnace lights. It continues to run for appr. 2 minutes and the high limit will open. It is not a variable high...

Goodman gmp075 will not light [ 4 Answers ]

Noob here, Goodman GMP075-3 . Vent kicks on, hear relays activate on circuit board, ignitor will not glow. Manually sucked on vent pressure switch hose to make sure diaphram is in, no results. Cut off both end of hose to ensure new tight fit with no pressure loss and reconnected, no change. Made...

View more questions Search