Ask Experts Questions for FREE Help !
Ask
    frazwood's Avatar
    frazwood Posts: 129, Reputation: 2
    Junior Member
     
    #1

    Nov 20, 2009, 09:50 AM
    Replacing a washer tray?
    I am working on replacing a vinyl floor with a ceramic tile floor (you can see this in another thread that I've started recently).

    I have just removed all of the vinyl floor and I am ready to start the actual project. This room also has our washer/dryer system. Our old floor had a washer tray permanently installed, including a floor drain in the middle of it (fully plumbed). The tray was cracked and damaged; so it's been removed.

    Although I am sorely tempted to simply cut the plumbing and cap it (i.e. remove the drain entirely), my wife wants to keep the floor drain and she'd like a permanently mounted washer tray. I've gone to Home Depot and Lowe's and they only have non-permanently mountable (i.e. removable) washer trays.

    Any suggestions of places where I could get a permanent washer tray?
    mtconc's Avatar
    mtconc Posts: 119, Reputation: 9
    Junior Member
     
    #2

    Nov 20, 2009, 03:59 PM

    Do you have a plumbing supply store near you.. I think that might help
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #3

    Nov 20, 2009, 04:41 PM
    Hi Fraz...

    To get a pan for your situation, most likely you will be best to pop over to a local sheet metal fabrication shop and have them make a pan up for you... no getting around it really! Do not go to a plumbing supply store for this as they will only call the local sheet meatl shop and then mark it up 25%... ;) Be sure to measure the size of the pan and know how high you want the walls of the pan to be.

    Pans can be copper or galvanized sheet metal... I recommend the galvanized here. Have the company install the drain/strainer directly into the pan so that all you need to do is connect the old pipe up using some pipe and a SHIELDED CLAMP (see image) to connect old/new together.

    How is the trap at the drain kept wet? Is there a trap primer?. there should be? Let us know if you want to discuss more here... glad to help.

    MARK

    .
    Attached Images
     
    frazwood's Avatar
    frazwood Posts: 129, Reputation: 2
    Junior Member
     
    #4

    Nov 20, 2009, 06:24 PM

    Mark and mtconc: Thanks for the suggestions. I was thinking about getting a plastic washer tray, as that's what I had before -- I hadn't thought of a galvanized metal tray.

    Also, the plumbing is PVC, so I don't even need the shielded clamp... that's the good news.

    I don't know how the trap for the drain is kept wet -- I've been wondering that myself lately. My best guess is that it's connecting somehow to the washer-standpipe and that keeps it wet. I'm sure that I'll find out tomorrow when I remove some of the subfloor to get at the plumbing.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #5

    Nov 20, 2009, 06:46 PM
    My bet...

    There's nothing keeping the trap wet. You may not have a trap... could just be a pipe connected to the outside in some way. If so, stick with that... ;)

    If not, and there is a PTRAP present that is not kept wetted by something then you will need to install a trap primer OR you will need count on pouring a gallon of water into the washer pan on a monthly basis.

    Keep us posted...

    MARK
    frazwood's Avatar
    frazwood Posts: 129, Reputation: 2
    Junior Member
     
    #6

    Nov 24, 2009, 01:00 PM

    Hi Mark:

    I never did figure out whether there was a trap. I was able to cut the old PVC and add the new plumbing without cutting into the floor.

    In the end, I basically plumbed it all like the drain of a tile shower -- it isn't the prettiest, but it'll be underneath the washer so it'll never be seen.

    My guess after reading your last post is that there is a trap primer already installed (although I don't even know that is... ). The house is 15 years old and the cities inspectors are more than a little fanatical about making sure that houses are built to code -- I cannot imagine them not catching a problem like that.

    Thank you very much for all of your help!
    Tim
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #7

    Nov 24, 2009, 03:34 PM
    Hi Tim...

    Sounds like you're all set for now... thank you for the update and the positive rating!

    MARK
    nofarms's Avatar
    nofarms Posts: 1, Reputation: 1
    New Member
     
    #8

    Jul 19, 2011, 10:15 PM
    Hi,
    I am looking for washer pan for my washing machine, that is a 25 x 27. I don't want it too be permanent. I am planning on moving it sometime down the road. I do however want it to drain, preferably at the back of the pan. The house is pier and beam.
    What advice do you have for me?
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #9

    Jul 20, 2011, 03:53 AM

    Hi NF

    Your best bet willprobably be to pop over to a local sheet metal fabrication company and have them make up a custom pan for you... should be a free quote and pretty cheap in most places... :)

    Mark

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Front Load washer/ overflow tray [ 7 Answers ]

We are potentially in the market for a front load washer. We currently have a top load located on our second floor and it sits in an overflow tray in the even it overflows (has happened before:( ) My husband did the plumbing for this tray and didn't get the angles and all that right so there is...

Replacing washer on Bath Faucet [ 2 Answers ]

Re the above,I am unable to unscrew the top of the faucet to replace the rubber washer,the top seems to have seized.Unfortunately whilst using the spanner the nut seems to have rounded of.Please advise . Regards, Ben

Replacing a shower washer [ 1 Answers ]

When I turn my shower handle to "on", only about half of the water converts to shower. The rest continues to come out of the faucet. I think that I need to replace a washer, but need some information on how to replace it.

Replacing Dishwasher with under counter washer [ 2 Answers ]

Hi, Is the plumbing that is in place for the under counter dishwasher able to handle the needs of an under the counter front loading washing machine? Thanks, condo79

Overflow ro leak tray for front load washer [ 1 Answers ]

I have just purchased a new front load Whirlpool washer with the stand that elevates the washer. The stand has a drawer that holds supplies... however it will not pull out with the leak tray installed. Is there a low profile tray or another method to protect against leaks. We just had our top...


View more questions Search