Ask Experts Questions for FREE Help !
Ask
    elahi101's Avatar
    elahi101 Posts: 2, Reputation: 1
    New Member
     
    #1

    Nov 17, 2009, 09:57 PM
    G40UHX Lenox gas furnace not working
    My LENOX gas furnace Model: G40UHX series does not work at all.

    I tried to start the furnace the main Blower kicks in.

    The Small blower does not run and Fire is not lit in ignite.

    The Air Condition Cooling unit is working.

    The Xformer has 27VAC output.

    Any body suggest what to chek and why?
    elahi101's Avatar
    elahi101 Posts: 2, Reputation: 1
    New Member
     
    #2

    Nov 17, 2009, 10:20 PM

    Also from Observation:

    The #2, #3 & #4 does not operate, what should Ilook for.

    when start set to call for heat it should be:

    1st ==within few second later the bigger/main blower should come on,blowing heat into the house
    2nd==the inducer motor comes on
    3rd ==after a few seconds the igniter should glow a pretty bright orange
    4th ==the gas valve open and burners fire up
    these steps are done in sequence 1-2-3rd-4th
    KC13's Avatar
    KC13 Posts: 2,556, Reputation: 99
    Ultra Member
     
    #3

    Nov 18, 2009, 11:11 AM
    Was the thermostat replaced since last heating season? If the circulating blower turns on first, the thermostat may not be configured for gas heating. Look on the back for a switch marked "E/F" or "E/G". If present, it should be set to "F" or "G".
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #4

    Nov 18, 2009, 04:25 PM
    Here is a complete service/parts manual for your unit. I suggest you keep a copy on your computer.

    http://0190acd.netsolhost.com/manuals/G40UH_Series.pdf

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Bryant Plus 80 gas furnace won't ignite burners [ 6 Answers ]

I own a Bryant Plus 80 gas furnace. The fan will run if I set the thermostat to "Fan On" instead of "Fan Auto". But the burners will not ignite. I have followed the user manual instructions to re-start the furnace, but that didn't work. I have a gas water heater and it is heating so I know the gas...

Carrier gas furnace code 31 [ 3 Answers ]

Hi. I have a Carrier gas (propane) furnace 58MCA100-11116 series 111. It shows a code 31. The evacuation blower runs for a short time then kicks off. The burners do not ignite. To date I have: replaced the pressure switch, checked in and out lines to the pressure switch for obstruction,...

Gas Furnace won't Light [ 1 Answers ]

I am trying to light my gas furnace in my house but it won't light. I light the pilot and when I turn the dial to on the flame goes away and no gas in going through! What am I forgetting or doing wrong?

Lenox Conservator furnace sparks but won't light [ 2 Answers ]

Hi all I need some help. My furnace has been working fine until today. Today when it tried to fire up I could hear it sparking for almost 5 min and it never would light. It is a Lenox Conservator Natural Gas furnace the gas valve has 4 wires attached to it. I can see the plug and it is sparking...

Lenox furnace problem [ 1 Answers ]

Have a 13 yr old Lenox furnace not staying lit continually. Lights for about 60 seconds kicks off for 2-3 minutes and back on again. Has a red light flashing. Anyone know what this could mean? Thanks


View more questions Search