Ask Experts Questions for FREE Help !
Ask
    DaBears's Avatar
    DaBears Posts: 7, Reputation: 2
    New Member
    		  
    #1

    Nov 2, 2006, 07:13 AM
    Goodman heat problem
    Goodman NG heater. Cycles to the ignitor, hear a click on the circuit board but no flame. Trouble light stays on steady showing no issues. Have replace circuit board, manually checked pressure switch, checked flo switches.
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
    		  
    #2

    Nov 2, 2006, 07:17 AM
    Can you check for 24 volts to the terminals of the gas valve after the click on the circuit board? If you have 24 volts on the gas valve, and no flame, the valve is bad.
    DaBears's Avatar
    DaBears Posts: 7, Reputation: 2
    New Member
    		  
    #3

    Nov 2, 2006, 07:22 AM
    Not getting volts after the click
    NorthernHeat's Avatar
    NorthernHeat Posts: 1,455, Reputation: 132
    Ultra Member
    		  
    #4

    Nov 2, 2006, 04:04 PM
    Follow the wires from the gas valve all the way back to the board one of the two wires will have some safety device in series with the valve. Pressure switch or limit, let us know what you find.
    DaBears's Avatar
    DaBears Posts: 7, Reputation: 2
    New Member
    		  
    #5

    Nov 3, 2006, 07:10 AM
    Found a switch that was stuck, replaced, now getting volts but still no flame. Replaced gas vlave on unit still same results. Replaced the gas valve prior to the unit, this seems to have corrected the problem.
    bdail99's Avatar
    bdail99 Posts: 2, Reputation: 1
    New Member
    		  
    #6

    Nov 3, 2010, 03:20 PM
    Try pushing the reset button on the limit switch located at the upper part of the heat manifold. I just had to do the same thing and that was my problem
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Heating Problem - Kenmore Heavy Duty 60 Series Soft Heat [ 4 Answers ]

My Kenmore Heavy Duty 60 Series Soft Heat Model 96565210will not heat on any setting. The dryer runs normally, it just won't heat at all. We did install a new heat element, and that would not heat up. Any help is appreciated!

I have AC, but no heat... Is the problem my furnace? [ 7 Answers ]

At first, my motor fan would cut off. After replacing the fuses, it kicked back on and I had cool AC. Later down the line, I noticed frost on the pip leading from the furnace to the motor fan. I purchased some insulating tape and called it a day. It seemed to keep it from freezing. Now, I tried...

Hot Water Heat Problem [ 3 Answers ]

I have a 5 zone hot water heating system. All zones work fine except for one. The zone valve opens when the thermostat goes on but the water pump and boiler don't go on. I am wondering of I need to replace the zone valve because maybe the current isn't passing through onto the pump to turn it...

Gas Dryer Heat Problem [ 3 Answers ]

I have a Maytag Gas LDG7600aaw dryer, 13yrs old. It recent stopped igniting the burner. When I first looked at it was full of lint and the igniter was working but would just go out with out lighting the gas. I shook the supply line the next time the igniter went on and it ignited the gas. I...

Heat Pump compressor fan problem [ 1 Answers ]

I have a Trane XE 1000 heat pump manuf. In 2002. Yesterday, the A/C started having a problem, I checked the units inside and out and found the compressor fan not operating. The outside unit was hot and louder than usual. I turned it off overnight and this morning turned it on to find the fan...

View more questions Search