Ask Experts Questions for FREE Help !
Ask
    klobbs's Avatar
    klobbs Posts: 1, Reputation: 1
    New Member
     
    #1

    Aug 22, 2009, 01:38 PM
    How do I wire a Miller furnace (E3EB-15H)?
    Hello,
    I recently bought a new furnace and need help hooking up the thermostat and power. I have a very basic understanding of wiring, but don't want to mess this up. Any help will be greatly appreciated. Here's what I have:

    Furnace model number: E3EB-015H
    Power supply 240VAC 1Ph 60 Hz
    4 speed
    I am using a jumper bar
    Thermostat: Honeywell Chronotherm IV Plus
    4 wires connected which went to the old furnace,
    (Intertherm 015HA):
    G,Y,W,R
    Outdoor Coil: Lennox 10ACB24
    Has one Red (L1) and one White (L2) wire which were also hooked to the old furnace.

    I'm having a friend replace the freon, but I'd like to hook it all myself. I can post wiring diagrams if needed. Thank you!

    -Kolby-
    pcampion's Avatar
    pcampion Posts: 19, Reputation: 3
    New Member
     
    #2

    Aug 25, 2009, 05:29 AM

    I looked up the Miller unit, and noticed it is for a mobile home. Does the unit have a terminal board (Usually by the blower area), with the G,Y,W,R? One easy way to wire the tstat is to use the color coded tstat wire, 4 wire usually has a green, yellow, white and red wire. Follow the same pattern, hook the green to the G, Yellow to the Y, W to the white, Red to the R, on both sides, Tstat and furnace. If you do not have the same colors, just make sure you hook the colored wire to the same spot on the furnace and Tstat (Match them) Do not hook Y at the tsat to w on the furnace, common mistake. Then take tstat wire from the furnace to the AC condenisng unit (2-wire will work, if not, run 4 or 5 wire and just use 2, usually white and red) Hook the red wire to the Y in the furnace (this is the cooling connection) and the white goes back to the common side of the transformer, usually designated as C. The Lennox unit will have 2 wires with wire nuts on them, the 24 VAC you ran from the furnace goes to these 2 wires, they should be in a small junction box near the contactor within the condensing unit. Good luck with it. Pat

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Miller Furnace [ 14 Answers ]

I have a Miller Furnace in mobile home. HAve had repairman twice and still not resolved. Problem: Sometimes the furnace doesn't "come on" when the thermostat gets to the point where it requires heat. If you touch the thermostat it just clicks - however if you open the furnace door & push button...

Miller Oil Furnace [ 3 Answers ]

I have a miller oil furnace that was installed in July of 2006 it has been running just fine until now I have power to it but it won't run. I can get the fan to start but when I hit the reset button all I get is the blinking light. Can you help:(

Miller furnace [ 1 Answers ]

I've got a natural gas Miller Furnace. This past weekend when I came home, the house was cold (62-ten degrees below setting) and I couldn't find anything wrong, so I just turned off and on the furnace, well it fired back up, but was only blowing air, not heating it up. There was a flame were it...

Miller furnace [ 1 Answers ]

I have no pilot light. The burner lights on full capacity at all times.

Miller oil Furnace [ 10 Answers ]

The light on the reset button keep flashing saying that it is locked out how can it be unlocked


View more questions Search