Ask Experts Questions for FREE Help !
Ask
    fedelstein's Avatar
    fedelstein Posts: 1, Reputation: 1
    New Member
     
    #1

    Oct 11, 2006, 12:31 PM
    Toilet doesn't drain all the way
    When you flush the toilet the water in the bowl (not the tank) doesn't go all the way down
    andrewcocke's Avatar
    andrewcocke Posts: 439, Reputation: 22
    Full Member
     
    #2

    Oct 11, 2006, 05:41 PM
    My toilet does this once in a while, normally after a major (you know). For me, its always something stopped up in the toilet, but not a hard block, just slowing it down, preventing the toilet from creating the siphoning effect when you flush.

    Plunge it real good for a while and see if that remedies it. Sometimes you have to get downright aggressive. But that also depends on the toilet.

    Ive also been told that a stopped up vent line for you drain can cause symptoms of this, but I have never had that be my problem, so maybe someone here has and can explain more.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #3

    Oct 13, 2006, 08:36 AM
    Quote Originally Posted by fedelstein
    When you flush the toilet the water in the bowl (not the tank) doesn't go all the way down
    I have one that most repair plumbers miss.. Look down at the bottom of the bowl. If there is a small hole, then that is a jet that starts the syphon action. If it's clogged the water will just swirl around and slowly go down leaving solids behind. Take your finger,(UGH! ) and run it around the inside of the opening. Over the years minerals build up and cut down on the syphon (flush) action. If it is rough or you feel build up, take a table knife and put a bend in it to get around the curve in the bowl and chip and scrap it clear. Next take a coathanger and clear out the holes around the rim. They start the swirling action. And last, check the water level in the tank. It should be 1/2" below the top of the over flow tube. And speaking of the overflow tube, Make sure the small 1/8" tube from the ballcock to the white overflow tube is connected so it discharges in it and that it's flowing when the ballcock fills. This is what raises the water level in the bowl. For a good solid flush they all have to work together. Hope this helps . Tom

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Slow Bathroom Sink Drain - but Tub and Toilet Drain Fine [ 4 Answers ]

I am hoping that someone can offer a suggestion to solve my problem. We recently purchased a 60 year old home. The sink in one of our bathrooms drains completely fine until the water has run for about 5 minutes and then all of a sudden it starts to back up and then drains very slowly. I have...

Toilet drain [ 3 Answers ]

I have been trying to install a new toilet in the basement and am unable to remove the bolts from the cast iron drain pipe.. Is there a way I can remove the entire drain and replace it with a new PVC drain or get a insert that will fit over the 4 inch drain.

90 in Toilet Drain? [ 1 Answers ]

I’m in the process of remodeling my basement, and would like to redirect a drain for a 1st floor toilet. The drain pipe currently comes through the floor, down to the bottom of the joist, takes a 45 towards the foundation wall and about 3 feet down the wall takes another 45 and then the pipe runs...

Toilet drain [ 1 Answers ]

We are building a new home and the drain plumbing for a toilet upstairs has a 90 degree elbow directly out of the clamp for the toilet, goes about 6 inches, another 90 degree elbow down into the trap. They could have went straight down into the trap, it appears, but put the extra piping in. I...

Toilet drain [ 16 Answers ]

I am remodeling my guest house. While I am reasonably handy, I know nothing about plumbing. This remodel involves reconfiguring the bath, specifically moving the toilet and shower. The problem is that the house was built on a slab (6" concrete). I have removed the concrete for the new lines but...


View more questions Search