Ask Experts Questions for FREE Help !
Ask
    hedgemonster's Avatar
    hedgemonster Posts: 1, Reputation: 1
    New Member
     
    #1

    Oct 2, 2006, 06:06 PM
    Utility tub drain tank
    I have a utility tub with a black tank under the tub.There is a tailpiece connecting the 2.The black tank has 2 electric cords running into it.How do I turn this on so it will drain? It is overflowing and does not come on by itself. Please advise
    iamgrowler's Avatar
    iamgrowler Posts: 1,421, Reputation: 110
    Ultra Member
     
    #2

    Oct 2, 2006, 08:50 PM
    Quote Originally Posted by hedgemonster
    I have a utility tub with a black tank under the tub.There is a tailpiece connecting the 2.The black tank has 2 electric cords running into it.How do I turn this on so it will drain? It is overflowing and does not come on by itself. Please advise
    Sounds like a sewage ejector with a mercury switch.

    One should plug into the backside of the other -- If this is the case, plug them into each other and then plug the remaining male end into a GFCI protected outlet.

    If it's already plugged into an outlet, check for other GFCI protected outlets in the circuit, if there are, see if they have been tripped, if they haven't or their aren't, then check the service panel for tripped breakers.

    Still no joy?

    Then plug the cords into a outlet with an extension cord that you know to be hot.

    Still no joy?

    A) The sewage ejector pump or mercury float switch is points up.

    B) The mercury float switch is hung up on something inside the sewage ejector bucket.

    C) You have a 'Little Giant' ejector system (or a reasonable facsimile) and the clean-out screens are plugged.

    If it's a 'Little Giant' ejector system, then remove the four bolts on the panel on the lid of the system and clean it out.

    If it isn't, plug the pump in directly and see if the pump cycles, if it does, then the mercury float switch has failed, if it doesn't, then the pump itself has failed.
    Attached Images
     

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Extending utility sink drain for bar sink [ 2 Answers ]

I have a utility sink in my walk-out basement - that sink's 1.5 inch drain connection is approx. 18" above the floor, into a two inch horizontal run. This 2 inch horizontal PVC runs about 3 feet, then connects to a main 3" DWV. I would like to add a bar sink, set into a standard height (36")...

All in one utility box... [ 5 Answers ]

I am looking for some kind of network device that would serve as a Router, print server Wireless access point and be able to handle T1 or fractional T1. Anyone heard of anything like this?

Adding a utility sink [ 1 Answers ]

I am planning on adding a utility sink to my laundry room, I was planning on tapping into the water lines and drain to the washer. I have not opened up the wall yet so I don't know the exact configuration of the drain, but my question is if I run the sink drain of off the drain from the washer...

Password utility for excel [ 4 Answers ]

There was a utility ( I think MS provided it) for forgotten passwords in excel. I have some spreadsheets archived from some very early xl days, (office pro 97) Is there a way to open these spreadsheets if the password is lost ?

Installing a utility tub [ 7 Answers ]

Hi, I want to install a utility tub in my laundry room. My question is, can I tee the tub drain into the washer drain stack? I really don't want to run a separate drain pipe all the way to the main stack ( about 30ft). About the house; single story, crawl space, laundry room at back of house,...


View more questions Search