Ask Experts Questions for FREE Help !
Ask
    GEO18's Avatar
    GEO18 Posts: 9, Reputation: 1
    New Member
     
    #1

    Apr 7, 2009, 05:52 PM
    Steel doors
    I have a sunroom with 2 steel doors that swing outword, is there anything I can do to stop the condensation on them in the winter months.( it is on the inside of the doors)or is there anything I can put on them .I can't put storm doors on them because they swing outword.
    21boat's Avatar
    21boat Posts: 2,441, Reputation: 212
    Ultra Member
     
    #2

    Apr 7, 2009, 07:05 PM

    If theses doors are inactive in the winter I would use foam board insulation on the inside to stop the condensation. The time for the cold to hot air mass is to rapid thus forming condensation.

    If the look doesn't bother you urethane foam is they way to go.

    Storms will help but it may not be enough

    Big box stores have it
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #3

    Apr 7, 2009, 07:35 PM

    If the foam doesn't appeal to you you can add a shrinking film seal all around the inside door frame, if you are not planning to use the doors. The problem stems from the fact that these doors have no insulation or are poorly insulated. They get very cold and the warmer moist air inside the home condenses. If you can't make the door warmer you prevent the air from reaching the door. Cost would be less than $15
    GEO18's Avatar
    GEO18 Posts: 9, Reputation: 1
    New Member
     
    #4

    Apr 7, 2009, 08:34 PM
    Quote Originally Posted by 21boat View Post
    If theses doors are inactive in the winter I would use foam board insulation on the inside to stop the condensation. The time for the cold to hot air mass is to rapid thus forming condensation.

    If the look doesn't bother you urethane foam is they way to go.

    Storms will help but it may not be enough

    Big box stores have it
    Unfortunately we do use these doors all winter any other suggestions
    GEO18's Avatar
    GEO18 Posts: 9, Reputation: 1
    New Member
     
    #5

    Apr 7, 2009, 08:41 PM
    Quote Originally Posted by ballengerb1 View Post
    If the foam doesn't appeal to you you can add a shrinking film seal all around the inside door frame, if you are not planning to use the doors. The problem stems from the fact that these doors have no insulation or are poorly insulated. They get very cold and the warmer moist air inside the home condenses. If you can't make the door warmer you prevent the air from reaching the door. Cost would be less than $15
    unfortunately we do use these doors all year any other suggestions?
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #6

    Apr 7, 2009, 08:50 PM

    here is a thought. A ceramic additive to paint.

    Ceramic Paint reduces the transfer of heat into your home

    If you look a dew point table, what you will find is the temperature in which moisture will appear. RH and temperature of the air and the temperature of the surface.

    You have to lower the RH or raise the temp of the door.

    So, options are:
    1. dehumidify (control with a dew point sensor - expensive)
    2. Insulate - (the ceramic paint)
    3. heat the door. Haven't figured out how.

    Make sure there are no air leaks.

    Replace the door with one with a higher R-value.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #7

    Apr 8, 2009, 07:05 AM

    I agree with the previous post but have a few additional thoughts. Buying a better door is the best option but heating the room more and increased circulation would help. You could also close the door between the home and sun room and open some windows to let the sun room reach outdoor temps. Your real problem is a combination of a steel door and poor insulation. Those two factors cause the sweeting and a new door, wood, can make it all go away.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Cut stainless steel [ 5 Answers ]

How do I cut holes in a stainless steel sink?

Replacing bedroom hollow doors with 6 panel pine doors. [ 4 Answers ]

I am replacing my bedroom hollow doors with 6 panel pine doors. My problem is that the 6 panel pine doors are not fitting properly. When I hung one door with the same size hinges I was able to put the screws in the same holes as the old ones but the door will not close. The new door is about...

Sharpening Steel [ 9 Answers ]

I recently got a few very nice Global knives for my birthday. LOVE them. As a budding home chef I never realized what a difference good knives made. The pamphlet that came with them says that I should use their special sharpening steel. It is both hard to find and expensive. Does anyone...

Steel Behind my brick? [ 2 Answers ]

I'm trying to run Sat cable and speaker wires into my house. Drill through brick no problem, then I hit something like steel, it's not magnetic, I'm burning up all my drill bit's.I thought may a stud or something, I tried another hole approx 6" over and same thing.Oh yeah I'm drilling about 5...

Steel Plate [ 1 Answers ]

I am drawing for a manufacturer to bend steel plate into a U shape. The steel is galvanised and 1.5mm thick. How do I show the Radius of the bend? What is the maximum radius I can bend with 1.5mm steel?


View more questions Search