Ask Experts Questions for FREE Help !
Ask
    mpnicholson's Avatar
    mpnicholson Posts: 2, Reputation: 1
    New Member
     
    #1

    Mar 22, 2009, 05:37 PM
    Shower insert wall seam leaks
    My upstairs bathroom shower is leaking. It is a fiberglass neo-angle with glass walls and a door.

    It leaks where the glass and metal wall meets the fiberglass on the bottom left side.

    We have caulked, after cleaning and drying it. It still leaks. It doesn't leak a lot, but we have 3 kids and it is their shower. I plan to live in the house until I die and want it to stop.

    Looking at the design, the metal wall just sits against the fiberglass insert. It isn't grooved or anything - only caulk keeps it from leaking.

    We are debating. Should we rip out the unit and put in a tile enclosure or she we get a better designed insert? Or are we missing something about sealing the leak?

    Any advice is welcome.

    Melissa
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #2

    Mar 22, 2009, 05:45 PM
    Melissa...

    I think you said magic words here...DRYING!

    I would remove the caulking that is present now and let it dry for a couple days. Then take a little rubbing alcohol and clean the entire area and let it sit for another day (alcohol will evaporate most of the remaining moisture)... then I want you to use a hair dryer to finish this 100%... let sit another day or so.

    Then you caulk... ;)

    It is all about DRYING TIME!!

    If there is any moisture trapped in any way under the metal... and there is... caulking can't dry!

    You could make this happen faster... but don't. Let things dry and you should have successful outcome.

    Let the new caulking dry an extra day or two, too... can't hurt. Otherwise, you are spending thousands to replace... right?

    MARK
    mpnicholson's Avatar
    mpnicholson Posts: 2, Reputation: 1
    New Member
     
    #3

    Mar 23, 2009, 12:34 PM
    OK - we have done all of that except the hairdryer part. I am confident that it was dry in there- it was over a week since it was used and 2 days since the alcohol was applied. We have used this method twice now.

    I feel like it is a design flaw- there is no flange connecting the glass wall to the bathroom wall.

    I guess it is worth trying again before we rip it out.

    Melissa
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #4

    Mar 23, 2009, 01:24 PM
    Hey Melissa...

    I had a customer turn on the water for just a second or two like 5 hours after installing the caulking... then I tried all the things I mentioned... NONE WORKED here either.

    I actually had to remove the caulking and the doors and clean and dry everything off before I could reinstall and recaulk everything so it finally stopped leaking.

    I hope this is not going to be the same for you... but be aware that it may just be the best option in this case.

    Almost all shower doors today simply rely on a bead of caulking for final seal (and screws holding the metal to wall)... so nothing abnormal there... ;)

    Good luck!

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Tub spout leaks at wall [ 9 Answers ]

I just installed a new tub with a tiled surround. The fixtures are brand new. I have a single handled water control and the shower diverter is operated by a pull rod on the tub spout. This is my question. When I lift the diverter to run the shower, I get water running out the back of the spout...

How to fix basment wall leaks [ 2 Answers ]

I have water coming into my basment through the walls. Mainly where the wall meets the floor. How can I take care of this problem.

Shower Leaks to Outside Stucco Wall [ 3 Answers ]

I have been reading the forums regarding leaky shower drain in a fiberglass enclosure and PVC drain pipe with much interest. My problem is that after a lengthy shower the stucco on the outside wall below my second floor shower gets damp and moisture appears to run out of an outside light...

Going from tile to insert in basement Shower [ 3 Answers ]

The shower stall is 30 deep by 31 wide and the drain is not in the middle of the stall. There is a couple of inched difference between the bathroom floor and the shower floor. I assume there is some kind of base that will need to come out when I tear the tile out. Does anyone make a muti-piece...

Going from tile to insert in basement Shower [ 2 Answers ]

The shower stall is 30 deep by 31 wide and the drain is not in the middle of the stall. There is a couple of inched difference between the bathroom floor and the shower floor. I assume there is some kind of base that will need to come out when I tear the tile out. Does anyone make a muti-piece...


View more questions Search