Ask Experts Questions for FREE Help !
Ask
    clauff's Avatar
    clauff Posts: 1, Reputation: 1
    New Member
     
    #1

    Jan 2, 2009, 01:30 PM
    High Amperage Thermostat
    I have a cabin in northern Minnesota where I keep the temperature at 50 degrees in the winter when we only get up there occasionally. I want to set up an emergency heating system in case the heat goes off and we cannot get back up there immediately. (I have an emergency sensor that calls if the temp drops below 50 degrees, which it would have done had we not been up there at that particular time when my gas furnace blower fan shorted out!) I plan to hook up four used eight-foot baseboard heaters in the basement that will draw about 35 amps on a 240 circuit, connecting from the electrical box to the units with 10ga. Wire protected with a 40A circuit breaker. I am looking for a thermostat that will trigger under 50 degrees that will handle this amperage.
    Is my plan sound, and do you have any suggestions on a thermostat?
    Thank you.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #2

    Jan 2, 2009, 01:36 PM

    So you must have a hard telephone line year round, right? There are systems like your that do more than just call. Not sure if the Ezra Group (http://www.ezragroup.com/) still sells their Talking Thermostat or the Commstat CEM but I have one that I can telephone and change the temp or start/stop a heating system. Or you can install a Honeywell TL8230A1003 -  $49.45 - Honeywell - Programmable Double Pole Line Voltage Thermostat for electric baseboards - TL8230A1003 which can be set as low as 40 degrees. The only shortcoming to your plan is most furnaces should not be set below 55 degrees or condensation will build in the heat exchanger.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

VARIABLY high thermostat readings; location NOT an issue; malfunction or miswired? [ 4 Answers ]

I just installed a new digital thermostat (HoneywellRTH230B) and I'm trying to figure out if it is malfunctioning, needs to be calibrated (if that's possible), or if I wired it backwards (if that's possible). This is a simple 24-volt 2-wire installation; thermostat is connected to the transformer...

Thermostat for high effic. Furnace [ 4 Answers ]

Company installed a GMV95 gas furnace, using my old Honywell thermostat, single stage. I believe that the 2-stage furnace needs a 2 stage thermostat. As of now the old thermostat is connected with 4 wires. If I upgrade the thermostat to a Honeywell visionpro RTH8500, won't I need an addit. 2 wires...

Dryer won't start, could it be the high limit thermostat? [ 13 Answers ]

My dryer is a Whirpool LE7760XWW0 The dryer won't start. If I unplug it and turn the timer, the timer doesn't run. If I plug it in, and the timer is set, it runs. (I forgot to check the power at the outlet, but with that, I'm assuming it is good.) I took the back panel off and began to...

Wiring Thermostat-High Voltage to 24v [ 1 Answers ]

I'm in the process of having my 1941 oil boiler replaced with a new gas boiler, and I want to replace my line voltage thermostat with a 24v programmable thermostat. At thermostat now is 110 with 1 black and 1 white. I know I will need a 24v transformer but don't know exactly how to wire this. Can...


View more questions Search