Ask Experts Questions for FREE Help !
Ask
    bheyward's Avatar
    bheyward Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Nov 29, 2008, 06:31 AM
    Wiring pump motor
    How do I wire a 240 volt 2 stage pump motor where does white black red wires go thanks
    bheyward's Avatar
    bheyward Posts: 3, Reputation: 1
    New Member
    		  
    #2

    Nov 29, 2008, 06:42 AM
    240 volt 2 speed motor
    How do I properly wire a 240 volt 2 stage pump motor where to place red white & black wires
    stanfortyman's Avatar
    stanfortyman Posts: 5,598, Reputation: 279
    Electrical & Lighting Expert
    		  
    #3

    Nov 29, 2008, 06:47 AM
    According to the wiring diagram on the motor.
    They are not all the same.

    This might help, althoiugh there is no diagram for a two-speed motor: http://catalog.wegelectric.com/img/Wiring_Diagrams.pdf
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #4

    Nov 29, 2008, 06:48 AM
    >>>>>>>>>Merged Two Posts<<<<<<<<<<

    Which is it , a two stage, two speed, or both?
    ansel's Avatar
    ansel Posts: 1, Reputation: 1
    New Member
    		  
    #5

    Dec 30, 2011, 06:05 AM
    Is that power in switch about motor pump but did not move o flow water in faucet? Wfat cause it?
    Mappey01's Avatar
    Mappey01 Posts: 1, Reputation: 1
    New Member
    		  
    #6

    Jun 23, 2013, 04:05 PM
    "I pulled a 110 electric pump from my old jacuzzi tub. It is a 2 speed pump. There are 4 wires. Green, red, black,and white/grey. How can I wire this motor to be able to use bothe speeds.I would like to replace my old, 1 speed pool motor.
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
    		  
    #7

    Jun 23, 2013, 04:17 PM
    You will also need the two speed switch from the old tub.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Condenser Fan Motor Wiring for Goodman AC Heat Pump 3 Ton [ 5 Answers ]

Condenser Fan Motor Wiring for Goodman 3 Ton -------------------------------------------------------------------------------- Hello Everyone, I have a GOODMAN A/C Heat Pump Model# CPLE 36-1 installed 3 years ago. Last week I turned the unit on, the compressor hums (not run)about 3-5...

Pump motor [ 6 Answers ]

The 5 hp electrical motor that drives the pump for my SPA will not start on low speed. When turned on it hums. I hit the Jet switch and the pump/motor comes on at high speed. I can then hit the Jet switch again and the pump/motor will run on low speed. When the set temperature is reached, the...

Wiring pool pump motor [ 2 Answers ]

I have a new pool pump motor. When I disconnected the old motor, I found it was wired with two blue wires and a green ground. The new motor has only L1 and L2 connections. How do I tell the difference? The pump was wired as a 220

Wiring pool pump motor [ 1 Answers ]

I have a new pool pump motor. When I disconnected the old motor, I found it was wired with two blue wires and a green ground. The new motor has only L1 nad L2 connections. How do I tell the difference?

Pool pump motor [ 0 Answers ]

Our pool pump motor plug has been replaced twice because when you try to plug it in it sometimes sparks and other times gets so hot it fusses to the outlet. Is this cord not grounded inside motor? Or any other suggestions? The pool is inground the pump brand is Lomart 1 hp & the motor is a baldor...

View more questions Search