Ask Experts Questions for FREE Help !
Ask
    Frank22's Avatar
    Frank22 Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Jun 17, 2006, 05:58 AM
    Yet another ceiling fan question
    I have successfully installed a ceiling fan before but the old house I now live in has wiring that baffles me. The Hampton ceiling fan I am installing has the usual black, blue, white, and green (ground) wires. The outlet does not appear to have any ground wires (so I will ground the fan to the metal box--right?) and the outlet contains 4 black wires, 4 white wires, and two red wires. Experimenting I can get the ceiling fan to work with the pull chain but I cannot get the wall switch to work. I now I am doing something wrong because this is a replacement fan and the wall switch used to work. Any advice would be really appreciated.

    Thanks!
    shunned's Avatar
    shunned Posts: 268, Reputation: 20
    Full Member
    		  
    #2

    Jun 17, 2006, 07:19 AM
    If you can supply power to the fan (it works on the pull chain) then put that wall switch in between the source and the wires going to the fan. Sounds like you have 4 circuits in that box. Do you know which circuit powered the fan previously?
    ceilingfanrepair's Avatar
    ceilingfanrepair Posts: 5,733, Reputation: 109
    Uber Member
    		  
    #3

    Jun 17, 2006, 10:18 AM
    It sounds like you have a switch loop in that box. Do you recall how the previous fan was wired? How many wall switches controlled it?
    Frank22's Avatar
    Frank22 Posts: 3, Reputation: 1
    New Member
    		  
    #4

    Jun 17, 2006, 10:56 AM
    Unfortunately, I did not take the fan down but I am told that the two red wires and two of the black wires were not attached to the previous fan. That would leave the two of the white wires and two of the black wires that ran the fan and light.

    The previous fan was turned on by only a single light switch before.

    Any suggestions?
    ceilingfanrepair's Avatar
    ceilingfanrepair Posts: 5,733, Reputation: 109
    Uber Member
    		  
    #5

    Jun 17, 2006, 11:22 AM
    Yeah, sounds like one black wire and white wire come from the power source, and the other set go to the switch. Can you tell which is which from looking in the box?
    Frank22's Avatar
    Frank22 Posts: 3, Reputation: 1
    New Member
    		  
    #6

    Jun 17, 2006, 11:50 AM
    Sounds like a good idea. I will take a look at them and see what I can do. If I figure this out which black/white pair would I attach to the black wire from the fan and which black/white pair would I attach to the white wire from the fan.

    Thanks!
    ceilingfanrepair's Avatar
    ceilingfanrepair Posts: 5,733, Reputation: 109
    Uber Member
    		  
    #7

    Jun 17, 2006, 11:53 AM
    Do you have a voltmeter or multi-tester?

    Although the thought occurs, if it was indeed a switch loop as I suggested, only one black and one white would connect to the fan, the other two wires would connect together. Was anything else on the switch with the fan? Did the switch have separate controls for the fan and light?

    This is more TK's territory.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Hampton Bay Romano Ceiling Fan Question [ 4 Answers ]

Hi. I recently purchased a home with a hampton bay Romano ceiling fan. There was no manual. I have tried to get into the light to change light bulbs and can't see to get it to open? Any ideas?

Southwind V ceiling fan question [ 4 Answers ]

I purchased a Southwind V ceiling fan from Home Depot. Being an electrician, I did not have too much problem installing the fan except when it came time to put the remote receiver in what they call the canopy cover. I am having a problem fitting the receiver inside the canopy cover. Thank you.

Ceiling Fan wiring question [ 15 Answers ]

I was trying to install a new ceiling fan this weekend and ran into a little problem. It looks like the previous owner cut the existing wiring in half so instead of 1 black, 1 white and 1 green wire I have 2 sets of each. Is this a normal wiring scheme? Do I just connect both blacks together, both...

Question about Hampton Bay Ceiling Fans [ 15 Answers ]

First, thank you for such great place where people can find answers to their questions. One of my two Hampton Bay ceiling fans stopped working. How can I check if there is a problem with my remote control or with that fan? It seems that there is no problems with power, because the lights...

Question about Texturing a ceiling [ 3 Answers ]

I read on-line on a do it yourself page to prime the ceiling first so after scraping the popcorn and patching all the nail dimples and repairing all the little scrape marks so I wiped the surface with a rag and primmed it with Kilz 2 Primmer. When I went to home depo to get some stuff for the...

View more questions Search