Ask Experts Questions for FREE Help !
Ask
    PAPADIESEL's Avatar
    PAPADIESEL Posts: 3, Reputation: 1
    New Member
     
    #1

    Nov 2, 2008, 07:38 PM
    John Deer Sabre gx1542b120004 Will not crank
    Have a John Deer Sabre gx1542b120004. Will not crank. Solenoid w/n energize. Just get a relay type click from front of engine. Have no wiring manual. Battery reads fully charged 12.0v. Only checked the seat switch so far. Can my battery still be the issue? THANK YOU IN ADVANCE!
    John C Bridgers's Avatar
    John C Bridgers Posts: 10, Reputation: 1
    New Member
     
    #2

    Nov 4, 2008, 08:50 AM
    Hello Papadiesel:

    From your Description it Sounds like a Safety Switch Problem. You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, John Deere - Parts Catalog and Enter the Model Numbers (Sabre) and Click Find. Then Select your Model from the Search Results Area. Then Select the Sectional File. Then Select the Section of the Mower you Wish to View Online. The Following is an Instruction File for the Safety Switch System. Any Input is Appreciated. The Color Code of the Wires May be Different than those I Use as a Reference in the Instruction File. **PLEASE REMEMBER THAT THE INSTRUCTIONS FOR CHECKING THE SAFETY SWITCHES IS JUST THAT!! FOR CHECKING ONLY. I NEVER Suggest a Mower be Operated with a Safety Device or Switch Disconnected or Bypassed. Now. On Some Model Mowers you can Simply Unplug the Safety Switch from the Harness. On Other Models you have to Place a Jumper Wire Between the Harness Terminals (on the 4 Post Switch (Clutch/Brake) Jumper from Same Color Wire white to White First and then Check for Fire, Now Include the Black to Black Wires if No Fire. Check the Clutch/Brake and the Blade/PTO Safety Switches First. Check the Seat Safety Last. Usually the Seat Safety is Not in the System for Starting the Engine. Just to Ensure Someone is in the Seat when Engaging the Transaxle and/or Blades. Use a Paper Clip or a Short Wire to Make a Jumper.** Usually if the Battery is Reading Above 12.0 VDC, then the Battery is Good. I Suggest you have the Battery Load Tested if there is ANy Doubt. Have Someone Watch the Volt Meter and Turn the Ign Switch to the Spring Loaded Start Position. If the Battery Shows Lower than 10.5VDC, then the Battery May have a Bad Cell and Require Replacing. If you Hit a Snag or this Does Not Correct the Problem, I am Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. Thanks.

    Good Luck

    Respectfully

    John

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

1998 John Deere sabre value [ 3 Answers ]

just wondered if anyone has an idea of the value of a John Deere Sabre riding mower, 16 hp, 42 " mowing deck runs great, starts every time. Thanks for your help.

John deer sabre won't start [ 1 Answers ]

I have a john deer sabre model 1438 gear. There is a wire that comes from a fuse that I do not know were it goes. I hooked it directly to the posative on the battery and I blow my fuse. I hook it to the selenoid were the powere wire connects from the battery and the fuse blows. I hook it to the...

John Deere Sabre Riding Lawnmower [ 2 Answers ]

Does anyone know where I can find a repair manual for a John Deere Sabre riding lawnmower? I have a problem with the battery keeping a charge. Hooked up a 12v trickle charge solar cell hoping this would charge the battery, but to no avail. It's like something is discharging the battery. I...

John Deere Sabre riding mower [ 2 Answers ]

I need to get the back wheel off my JD Sabre mower. It looks like there is a shear pin that is holding it on after I get the big snap ring off. How do I get the pin out?


View more questions Search