Ask Experts Questions for FREE Help !
Ask
    hammell's Avatar
    hammell Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Nov 2, 2008, 02:58 PM
    My Comfortmaker enviro plus 90 fan blows ALL the time.
    My Comfortmaker enviro plus 90 fan blows ALL the time:confused:. Ive changed the batteries in thermostat no change:(. Ive taken the thermostat off the wall while it was running no change:confused:. I just purchached a new programmable thermostat today, installed it and the same, no change:mad:. There's no change in the temp even with it on heat or cold from the highest to the lowest temp:mad:. As of now I turn the unit on and off at the source. It started at the end of winter - beginning of spring earlier this year. Please help if you can. Thanks.
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Nov 2, 2008, 05:44 PM
    If you can find your circuit board in the furnace see how many blinks happen on the trouble light and then look at the inside of the blower door for a answer to the number of blinks.
    hammell's Avatar
    hammell Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Nov 2, 2008, 09:09 PM

    It has no lights on mother board. The fuse is good also. Could it be a (the) relay switch?
    hammell's Avatar
    hammell Posts: 3, Reputation: 1
    New Member
    		  
    #4

    Nov 2, 2008, 09:10 PM
    And how should I know if the furnace pilot light is light?
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #5

    Nov 2, 2008, 10:00 PM
    I do not believe you have a pilot that is lit manually. You have a form of auto ignition probably HSI.

    I thought you were having a problem with the blower and now mention (( and how should I know if the furnace pilot light is light?))

    The blower could be a relay and if your circuit board has a relay on it for the blower it could be bad. There could also be another relay mounted to the furnace off the circuit board. LOOK on the back side of the blower door panel for a wiring diagram. All furnaces have on there and trace out the circuit.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Comfortmaker Furnace [ 1 Answers ]

My comfortmaker furnace doesn't have enough upward angle on the exhuast to create the external pressure needed for the furnace to run. So, the furnace comes on and cuts off. My water heater has a fan on the exhaust so that when it kicks on the exhaust fan comes on and helps exhaust the gas...

Comfortmaker [ 1 Answers ]

Not cooling

Comfortmaker Furnace [ 2 Answers ]

I recently purchased a new Comfortmaker Furnace, the problems is it runs for approx. 4-1/2 minutes, shuts off and then comes back on in 2 minutes. I have had a couple of people check and they said that nothing is wrong with it. Any suggestions on what the problem might be?

Comfortmaker Furnace Fan blows in line fuse and will not allow furnace to work [ 1 Answers ]

I have a Comfortmaker Furnace (approximately 1998/99) and the fan will not turn on allow the furnace to heat. When I try to turn the furnace on it blows a 3 amp fuse at the blower motor. I removed the fuse and jumped it and all it will do is make a faint buzzing noise and not turn on. I can...

Comfortmaker [ 1 Answers ]

My Unit Has A Loud Running Noise And Upon Shut Down There's A Loud Clank Sound... What Could It Be

View more questions Search