 |
|
| Browse | Ask | Answer | Search | Join/Login |
|
|
||||
|
It is easy just remove the handle, pull the U pin and pull out the cartridge. If you phone Moen 800-465-6130 they will send you a cartridge for free. Also on the MOEN Kitchen Faucets, Bathroom Faucets and Bathroom Showers website there is an animated tutorial showing how to remove the cartridge.
|
||||
|
||||
|
Hello dreamer,
Click on the link below it will guide you step by step how to replace the cartridge. As kaylar says If you are the original owner of the house call Moen help line in U.S at 800-289-6636 they will send you replacement for free, Good Luck. Installation Help / Animated Tutorial - Installing the Moen 1225 / 1200 Cartridge |
||||
|
||||
|
Hi all:
Hey Dreamer7, as suggested... not a real hard job, but wanted to pop in and make sure you understood a few things... ok? 1) No washers to change here... just a cartridge assembly (see pic. #1) 2) Need to shut the cold water to the house OR need to shut hot and cold water to the shower valve before beginning. 3) Follow the links above... Afaroo's get you there fastest! 4) Remove handle, remove retainer clip and then will need to pull/yank (hold valve against yourself) on the cartridge assembly to remove it. If have great difficulty removing the cartridge (you shouldn't, but just in case... ;)) then moen sells a MOEN CARTRIDGE PULLER (see pic.#2) at local home supply store... but hopefully don't need it. 5) Order a replacement cartridge before beginning the job or pick up a moen replacement cartridge #1225 at local home supply store. 5) As already stated by these guys... Moen will ship you a free cartridge assembly (including shipping), but it can take up to 10 days so don't go disassembling the unit until the part arrives. You just need to tell them that your cartridge needs to be replaced due to dripping and they should send new cartridge right away. 6) Moen has express delivery of part ($12.00) that gets that cartridge to you in 2 days... just so you know. Finally, not a bad idea to pick up a little silicone grease from a home supply store (or ask Moen people to send you small container) to lubricate the oring prior to installing the new cartridge. Don't get any on the cartridge parts... just on the O ring and cartridge will slide in easy! Then replace retainer clip, trim and handle. Then test water... if hot and cold are reversed simply remove cartridge again and rotate it 180 degrees... that will fix that! Let us know if have any more questions... MARK |
||||
| Question Tools | Search this Question |
Add your answer here.
Check out some similar questions!
I've read most of the questions on this website about this matter, but I'm still confused. I pulled off the handle and wall plate. But what do I do after that? I see a small (4 inch approx.) hole in the wall with a "unit" that looks like a cartridge that holds the handle. I can turn it to hot...
I am getting no hot water from my Moen single handle shower valve. I have plenty of pressure from cold water side. I removed the main handle to expose the valve. The hot water pipe has a small valve with a common head valve stem which I turned, hoping to unblock the valve, but this had no...
The shower is dripping and I am trying to get to the stem by removing the handle. I can see a set screw recessed into the bottom of the handle. I have tried an allen wrench but bent it without any success.
I have a Moen single handle valve in my bathtub. The tub spout has a diverter on the top to change it to shower mode. Recently I tightened the screws on the cover plate where the handle attaches to eliminate slack which was causing the tub spout to move (and pull caulk away) each time the shower...
I have lost significant pressure in my shower equipped with a Moen single handle pull out and rotate - R or L. I have a 2nd shower with identical unit - swapped cartridge - no change. Pulled out the posi-pressure valve on the hot side and found some debries, no change in pressure, may be worst....
View more questions Search
|
