Ask Experts Questions for FREE Help !
Ask
    Oneill474's Avatar
    Oneill474 Posts: 427, Reputation: 2
    Full Member
     
    #1

    Jun 11, 2008, 01:52 AM
    Fan starts slowly
    Have a floor fan that starts slowly. Blades barely turn for a few minutes.
    Then it starts and runs okay for the rest of the day. Someone told me its
    The starter capacitor. Fan only cost $13.00. Just curious about the problem.
    WVHiflyer's Avatar
    WVHiflyer Posts: 384, Reputation: 34
    Full Member
     
    #2

    Jun 11, 2008, 03:45 AM
    I just fixed one w/ same prob. The spindle is probably dirty (dust mixed w/ grease). Remove blade (probably lock on front turn clockwise to loosen), and try some WD40 or penetrating oil where spindle enters housing. (I had to take mine apart and move shaft 'in & out', cleaning and relube... but it was a bit more expensive fan... )
    ceilingfanrepair's Avatar
    ceilingfanrepair Posts: 5,733, Reputation: 109
    Uber Member
     
    #3

    Jun 11, 2008, 11:10 PM
    Do NOT use WD40 as an oil, it will ultimately cause problems.

    For oiling, follow these instructions:

    Oiling your ceiling fan - Ceiling Fans N More

    To the original poster, what make/model is the fan?

    General ceiling fan troubleshooting and help FAQ- Ceiling Fans N More
    WVHiflyer's Avatar
    WVHiflyer Posts: 384, Reputation: 34
    Full Member
     
    #4

    Jun 12, 2008, 10:59 AM
    I do know there are some places WD40 can cause probs (in a lock... ) but since there was grease on the spindle in my fan anyway, what prob would WD40 cause?

    BTW - is not ceiling fan
    ceilingfanrepair's Avatar
    ceilingfanrepair Posts: 5,733, Reputation: 109
    Uber Member
     
    #5

    Jun 12, 2008, 12:17 PM
    WD40 is not an oil. It will in fact dry up all the existing oil in the bearings, causing metal-on-metal contact. I use it to clean bearings and then thoroughly replace with fresh oil.
    WVHiflyer's Avatar
    WVHiflyer Posts: 384, Reputation: 34
    Full Member
     
    #6

    Jun 12, 2008, 01:50 PM
    Sorry about the incompletion in comments... fingers flying over keyboard too fast... As I tried to ask, didn't the WD originally stand for "Water Displacement"? I just didn't realize it would also displace oil.
    ceilingfanrepair's Avatar
    ceilingfanrepair Posts: 5,733, Reputation: 109
    Uber Member
     
    #7

    Jun 13, 2008, 04:06 PM
    Yep :) It is a "penetrating oil" which means it eats through pretty much everything. I used to use it to clean brass plating until I learned it ate through lacquer.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

It is been too slowly. [ 5 Answers ]

Hi, Recently, I have a problem with my internet speed. When I first enter website (Yahoo) it is no problem. Then I try to enter website under my mail. It takes forever more than 10 minutes. It doesn't allow you exit either. It is freezed. It said Microsoft explore not responsed, sometimes it...

Tub Drains Slowly [ 11 Answers ]

I recently changed the plumbing for a tub-shower from the old galvanized pipes to ABS pipes. I changed the entire drain from the Overflow to P-trap, vent connection and past the sinks. Everything seems fine, I pretty much configured it in the same way the old pipes had been, but it drains pretty...

Inducer motor starts running, but ignition never starts [ 1 Answers ]

I have a Payne Gas forced air furnace, and it's behavior has changed in the last couple of days, where it never gets past the Inducer motor cycle. When we turn on the thermostat (or even jumper across the "R" and "W" leads on the furnace controller) the inducer motor starts running and keeps...

Tub Drain Very slowly [ 5 Answers ]

I am having trouble with a tub drain in a house that I have just moved into. The tub take about an hour to drain. I have tried drain cleaners, and they help a little for a short time but will still take 20 to 30 minutes to drain. I have tried to pulling out the drain lever on the tub witch is a rod...

Tub drains slowly [ 2 Answers ]

Ok, I've got one for you all... Our bathtub in the master bathroom drains slowly. A common problem that seems to be caused by grease and hair clogs. But I don't believe this is the problem. Here is my situation. The bathroom has two sinks, toilet and separate shower. All of which drain...


View more questions Search