Ask Experts Questions for FREE Help !
Ask
    ccamml's Avatar
    ccamml Posts: 2, Reputation: 1
    New Member
    		  
    #1

    May 31, 2008, 09:00 AM
    Blower unit works when it wants
    I have a 2002 L100 Saturn. The blower works when it wants to. I can feel the compressor kick on. When it does work it works great. Does not matter what setting 1,2,3,4. What can cause this?
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
    		  
    #2

    May 31, 2008, 10:06 AM
    Try spraying control panel buttons with WD-40--wipe off excess.
    ccamml's Avatar
    ccamml Posts: 2, Reputation: 1
    New Member
    		  
    #3

    May 31, 2008, 04:38 PM
    Quote Originally Posted by ccamml
    I have a 2002 L100 Saturn. The ac blower works when it wants to. I can feel the compressor kick on. When it does work it works great. Does not matter what setting 1,2,3,4. What can cause this?
    Are you talking about spraying the swivel switch on the outside dash above my hot cold/ac/rear defrost?
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
    		  
    #4

    May 31, 2008, 04:56 PM
    You have to use your own judgment, but I thought you may have control buttons.
    archie12345's Avatar
    archie12345 Posts: 7, Reputation: 2
    New Member
    		  
    #5

    Jun 2, 2008, 07:00 PM
    I don't really recommend spraying anything. I think your blower motor needs to be replaced.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Blower works on A/C but not on heat or fan only [ 1 Answers ]

I have a 1997ish intertherm A/C unit, when the Air is on the blower works fine, but when I switch to heat or fan only the blower will not work? I have bought a new blower relay & capacitors. I tested the sequencers for 240 & 24 volt, everything is reading good. I am at a loss, does anyone have...

Blower turns on and off / flame works fine [ 1 Answers ]

I have a Luxaire Delux High Efficiency Furnace (PBNU-LD12N1000)that probably isn't to efficient since it's about 15 years old. I recently bought a new home and have had trouble with the blower in the furnace turning off before the house is heated to the correct temp. It will then turn itself back...

Gas Furnace / AC unit fan works. Heat/AC do not [ 2 Answers ]

This winter the furnace control board in my Lennox Gas Furnace / AC unit failed and I had it replaced by a contractor. The contractor mis-wired the thermostat inputs to the board. He wired the Green (fan) wire to the C (compressor connection) board input and the C wire to the Green (fan) board...

Blower fan works in A/C but not heat [ 8 Answers ]

A couple of weeks ago my Lennox G20Q3E-75-1 was acting up. Gas valve was cycling when calling for heat and then once satisfied and the main burners went out the pilot light was staying lit. I thought it might be the flame sensor as far as the gas valve cycling and didn't want to tear into it so I...

Blower works intermittently for A/C [ 1 Answers ]

I have an old York furnace with central air. When turning on the A/C, sometimes the blower comes on, sometimes it doesn't, and sometimes it toggles off and on with a loud clicking sound. If I use the manual switch on the limit control, everything is fine, but of course, then the blower is on...

View more questions Search