Ask Experts Questions for FREE Help !
Ask
    cstewart74's Avatar
    cstewart74 Posts: 1, Reputation: 1
    New Member
    		  
    #1

    Apr 23, 2008, 06:37 PM
    Pop and then water turns off
    Hello, I have a plumbing problem. I just replace the stem and the back nut thing that I needed to buy a special wrench to take out the old and install the new. That was about a month ago. No problems until tonight when I turned on the cold water in my shower. I got a pop sound (just once) and the water flow stopped. I kept twisting the faucet, and the water flowed again like there was never a problem. I repeatedly turned on and off the water with the same outcome every time. So my question is how do I fix this? Any suggestions would be greatly appreciated. Thanks in advanced.
    EPMiller's Avatar
    EPMiller Posts: 624, Reputation: 37
    Senior Member
    		  
    #2

    Apr 23, 2008, 07:17 PM
    Your terminology is not very specific. Sounds like you replaced the stem and seat in a compression valve faucet. If the seat does not have a snug fit in the threads, the opening and closing of the valve will work it loose and you can have problems like you describe. It depends on the specific design as to exactly what happens. I put teflon tape or some type of pipe dope on the threads before installing a new seat. That helps prevent the seat from loosening. It also prevents a drip from water going around the new seat. (I've had it happen.) It could also be the stem, there are some interesting designs out there.

    Take everything apart, pay attention to how it comes apart and whether it is exactly as you put it together the last time. Probably not. Then put it back together with a couple wraps of teflon tape around the threads of the seat and possibly the screw that holds the faucet washer in place too.

    EPMiller
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #3

    Apr 24, 2008, 04:47 AM
    Can you give us the brand name of the faucet. I assume it's a two or three handled valve and not a single handled one. DO NOT put Teflon Tape on the threads of the stem or the bonnet packing nut. You can coat the threads with plumbers heat proof grease for easy operation if you wish.
    when I turned on the cold water in my shower. I got a pop sound (just once) and the water flow stopped.
    .
    You either have a small pebble in the cold water supply or the screw holding the washer has came loose and the washer's blocking the seat.
    Shut the water off and remove the stem and washer assembly. Check that the washer's on tight. Now, with the valve still opened up, turn on the cold water supply to flush out the supply and the open valve body. Reassemble and test. Better now? Regards, Tom
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Water handle turns wrong way after I installed new water valve [ 6 Answers ]

Water handle turns wrong way, after I installed new water valve

Well pressure switch turns off water [ 1 Answers ]

I have a submersible well pump with a pressure tank and a square-d pressure switch. I have it set to cycle between 30 and 65 lbs. Sometimes when the garden sprinklers are on and it swiches stations so two stations are on momentarily and the pressure is close to the low setting (30lbs) it will...

Hot water turns cold [ 1 Answers ]

We have an old furnice (15-20 years old) that I think heats the hot water on demand as we have no hot water tank (apart from the overflow). We use oil as a fuel and have hot water radiators in one zone and baseboards in a second zone. The problem is that when we go to take a shower it starts very...

Hot water turns off in shower when someone else uses water [ 5 Answers ]

The water temperature changes drastically when taking a shower when someone else turns on another faucet or flushes the toilet. Is there any way to prevent this? Thanks.

View more questions Search