Ask Experts Questions for FREE Help !
Ask
    mr500's Avatar
    mr500 Posts: 181, Reputation: 8
    Junior Member
     
    #1

    Mar 26, 2008, 05:05 PM
    Torqueing Breakers
    When installing breakers and such, I know that there are torque specs, but Im just wondering how many actually torque the wires as opposed to tightening really good?

    I have torque wrenches lol that would do the job, but is it overkill? Just a newbie question is all
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
     
    #2

    Mar 26, 2008, 05:11 PM
    Never heard of torqueing breakers. The lines from the pole are supposed to be torqued to a certain torque (in inch pounds) but never heard of torqueing breakers. I know a bit about residential wiring but am not an electriction.
    mr500's Avatar
    mr500 Posts: 181, Reputation: 8
    Junior Member
     
    #3

    Mar 26, 2008, 05:14 PM
    Quote Originally Posted by hkstroud
    Never heard of torqueing breakers. The lines from the pole are supposed to be torqued to a certian torque (in inch pounds) but never heard of torqueing breakers. I know a bit about residential wiring but am not an electriction.

    The breakers do have torque specs on them as so do the lugs in my cub box. In the past I have just tightened them really really good. Have yet to have a problem
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #4

    Mar 26, 2008, 05:48 PM
    In production, it makes a lot of sense. There are torque screwdrivers, but their pricey.
    When I worked on my car, I would torque just about every bolt and spark plug. Lugnuts included. I would generally always apply anti-seize as well.
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
     
    #5

    Mar 26, 2008, 06:52 PM
    Yes but you are an engineer KISS. A mechanic torques by one grunt or two grunts. Let me rephrase, I have never heard of a code requirement to torque breakers.
    mr500's Avatar
    mr500 Posts: 181, Reputation: 8
    Junior Member
     
    #6

    Mar 26, 2008, 07:19 PM
    OK thanks guys. Its just I seen the torque specs printed on the sides of breakers lugs and so forth. I was just curious

    Thanks
    Mike
    shader's Avatar
    shader Posts: 235, Reputation: 12
    Full Member
     
    #7

    Mar 26, 2008, 08:05 PM
    hkstroud/mr500---Article 110.14 addresses Electrical Connections---FPN: Many terminations and equipment are marked with a tightening torque. The commentary section then states that Section 110.3(B) applies where terminations and equipment are marked with tightening torques. ---Any listed/labeled eqpt. Shall be installed and used in accordance with any instructions included in the listing/lableling. So, if torque values are listed (they're listed for a reason) they should be followed. If that is practiced in the field, I can't say.

    Also, if your mechanic tightens things up with one or two grunts, it's time for a new mechanic :eek:

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

What breakers would I need [ 1 Answers ]

In my rv cabin I will have a small 4.6cubit foot refrigerator, a 5.0 small freezer, a small 2.5 gallon hot water heater, a small 5000btu a/c and 2 shop lights, I will have a 50amp hook-up, which breakers would I need to handle these things with a 50amp hook-up?

Circuit breakers [ 6 Answers ]

If I have a main disconnect at the pole what kind of breaker box should I put in my quanset To replace the old fuse box,a main lug or main breaker. This is also part my shop. Thanks for any answers, can omeone please help??

Fuses v breakers [ 3 Answers ]

thought I'd look on the web for this and I found this site. Here goes... my building was built in 1939 and has old cloth wire in it. My neighbors have all had their fuse boxes upgraded to circuit breakers, and since I recently fried a wire inside a conduit while hanging a fixture, I thought...


View more questions Search