Ask Experts Questions for FREE Help !
Ask
    Sunaina's Avatar
    Sunaina Posts: 80, Reputation: 1
    Junior Member
     
    #1

    Feb 3, 2008, 05:49 AM
    How to run Aspire 1410 recovery CD?
    Hi,
    I bought my labtop(Acer Aspire 1410) and window XP home edition was pre-installed. Now I want to renew my system/ recover. I got Window XP recovery CD but there is a special method to run that CD, because it dosen't run itself and I tried to put command :C but it didn't work...

    Can you tell me how to run that CD... Thanx a lot.
    PolluxCastor's Avatar
    PolluxCastor Posts: 117, Reputation: 5
    Junior Member
     
    #2

    Feb 3, 2008, 08:10 AM
    Try putting the CD in the drive and rebooting the computer. This should boot from the CD and start the install process.

    Do not continue with this until you have saved, in some manner, all the data on the drive you want to keep.

    If you have more specific questions on what to expect as you reinstall Windows, ask again before you start.
    ScottGem's Avatar
    ScottGem Posts: 64,966, Reputation: 6056
    Computer Expert and Renaissance Man
     
    #3

    Feb 3, 2008, 09:41 AM
    As Pollux said you need to boot to that CD. If that doesn't work. Go into your CMOS setup and make sure the CD is in the boot sequence.
    seahwk83's Avatar
    seahwk83 Posts: 3,276, Reputation: 212
    Ultra Member
     
    #4

    Feb 3, 2008, 07:22 PM
    Here you go - your going to start with step 3, post back if problems, I have a copy of users guide


    1 Restart the system.

    To the instruction "Press <F2> to Enter BIOS" is shown at the bottom
    Of the screen, during POST.

    3 Press <Alt> + <F10> at the same time to enter the recovery process.

    For the message "The system has password protection. Please enter
    000000:" is displayed.

    5 Enter six 0s and continue.

    6 "Acer Self-Configuration Preload" window appears.

    7 Use the arrow keys to scroll through the items (operating system
    Versions) and press "Enter" to select.
    Setup password and exit

    Press "F3" to setup password or press "F5" to exit the system recovery
    Process when "Acer Self-Configuration Preload" window appears.

    If "F3" is pressed, the next screen shows "Please enter new password:"
    Enter one to eight alphanumeric characters. You will be asked to reenter
    Your password for confirmation before continuing.

    The screen will display "Password has been created. Press any key to
    reboot...", hit any key to reboot your system.

    If "F5" is pressed, the recovery process will be terminated and the system
    Will reboot and start normally.

    Important: This feature occupies 2 GB in a hidden partition on your hard drive
    Sunaina's Avatar
    Sunaina Posts: 80, Reputation: 1
    Junior Member
     
    #5

    Feb 4, 2008, 05:11 PM
    Thanks a lot for your help... it helped:)

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Floppy Recovery [ 1 Answers ]

Hi, I have a floppy disk that is refusing to open.I have tried a couple of computers without response. How do I use the CHKDSK feature? Is that the way to go? Help. Ishmael

Yahoo ID Recovery? [ 1 Answers ]

Is there a way to recover a deleted Yahoo email Address and Yahoo Messenger ID?

Run, Cindy, Run [ 4 Answers ]

Fresh off her retirement from the antiwar movement a month and a half ago, Cindy Sheehan is not only embarking on a caravan and "walking tour" to Washington DC, she is threatening to run against Madame Pelosi if she "does not file articles of impeachment against Mr. Bush by July 23." All I can...

Run, Hillary, Run! [ 2 Answers ]

Someone is getting a good chuckle and probably making a mint. Why did I not think of this? A reversible bumper sticker. Democrats can use it on the rear, Republicans can use it on the front. http://www.bumpertalk.com/bt/images/items/BD513A.jpg ------------...


View more questions Search